keepcalculator

06 Numbers and Powers

Cardo Helmet Fit: Choose Mic Mount & Speakers

Card No. 06·74162 · Updated · Standard formula, shown below

Choosing the right microphone mount and speakers for your Cardo communication system depends entirely on your helmet’s interior layout, the type of riding you do, and how the helmet’s cheek pads and speaker pockets are shaped. This guide walks you through the specific fit considerations, mounting options, and speaker choices so you get clear audio and reliable voice pickup without discomfort or wind noise.

How Cardo Systems Fit Inside Helmets

Cardo’s communication units (like the Packtalk and Freecom series) are designed as universal fit, meaning the main unit clamps onto the left side of your helmet’s shell, and the speakers and microphone route inside the liner. The fit is not one-size-fits-all: it depends on your helmet’s internal dimensions, the thickness of the cheek pads, and the location of the speaker pockets. Most modern full-face and modular helmets have pre-cut speaker recesses in the liner, but the depth and position vary. The microphone can be mounted on a boom arm that extends from the main unit or on a wired clip that attaches to the chin strap or the inside of the chin bar. The right choice is the one that places the mic close to your mouth without touching it, and the speakers directly over your ear canals without pressing too hard.

Choosing the Right Microphone Mount

Cardo ships with two main microphone options: a boom microphone and a wired microphone. The boom mic is a flexible arm that extends from the main unit and positions the mic near your mouth. It is ideal for full-face helmets where the chin bar provides a stable mounting surface. The wired mic is a small capsule on a short cable that you attach to the inside of the chin bar or to the chin strap. It works best for open-face, half, and modular helmets where a boom would be too long or obstruct your face.

When choosing, consider your helmet’s chin bar depth. A deeper chin bar (like in many touring helmets) gives more room for a boom mic to curve inward. A shallower chin bar (common in sport and adventure helmets) may require the wired mic to get close enough. Also, check where the main unit sits: the boom mic must reach from the unit’s speaker/mic jack to your mouth. If your helmet has a very thick cheek pad, the boom may not reach far enough; in that case, the wired mic with a longer cable is the better choice.

How to Mount the Microphone Correctly

Proper mic placement is the difference between clear voice commands and a garbled mess at speed. Follow these steps for either mic type:

  • Boom mic: Attach the boom arm to the speaker/mic jack on the main unit. Bend the arm so the mic capsule sits just inside the chin bar, about 1-2 cm from your lips. Angle it slightly downward so wind from the vents doesn’t hit it directly.
  • Wired mic: Peel the adhesive backing and stick the mic capsule to the inside of the chin bar, centered on your mouth. If your helmet has a fabric chin curtain, you can also clip it to that. Ensure the mic is not touching your lips or chin – a small gap prevents plosive sounds.
  • Both: Route the cable along the inside of the liner, under the cheek pad, and into the main unit’s jack. Use the included velcro or adhesive clips to keep the cable from dangling.
  • Test: With the helmet on, say a few words and ask your intercom partner to confirm your volume and clarity. Adjust the mic position if you sound distant or muffled.

Selecting the Right Speakers

Cardo systems come with 40mm JBL speakers (on most current models), but you can upgrade to 45mm JBL speakers for louder, richer sound – if your helmet has room. The key is the speaker pocket depth and the space between the pocket and your ear. Here’s what to check:

  • Pocket depth: Measure the recess in your helmet liner. The 40mm speakers are about 10mm thick, while 45mm speakers are about 12mm thick. If the pocket is shallow, the speaker will press on your ear, causing pain.
  • Cheek pad thickness: Thicker cheek pads push the speaker closer to your ear. If you have thick pads, you may need thinner speakers or to remove some foam from the pocket (if the liner allows).
  • Ear anatomy: If your ears stick out, you’ll need extra space. Some riders use thin speaker spacers or cut a small hole in the liner for the ear to sit in.

If your helmet lacks speaker pockets entirely, you can carefully cut a shallow recess in the EPS foam liner – but only if you’re confident and use a sharp blade. Never cut into the structural shell. Many riders prefer to use the included velcro to attach the speakers directly to the liner, but that often makes them sit too far from the ears.

Common Fit Problems and Solutions

Even with the right components, fit issues arise. Here are the most frequent problems and how to fix them:

  • Speakers press on ears: This is the #1 complaint. Solution: use thinner speakers (40mm instead of 45mm), or remove some foam from the cheek pad under the speaker. You can also buy aftermarket thinner speaker covers.
  • Mic picks up wind noise: The mic is probably too close to a vent. Reposition it away from the chin vent, or use a foam windscreen (Cardo includes one).
  • Voice sounds distant: The mic is too far from your mouth. Move the boom arm closer or reposition the wired mic.
  • Helmet feels tight: The main unit clamp may be too thick for your shell. Try repositioning the clamp to a thinner part of the shell edge, or use a different clamp (Cardo includes multiple sizes).
  • Speakers rattle: The speaker is vibrating against the liner. Secure it with the velcro and ensure it’s fully seated in the pocket.

Comparing Boom vs. Wired Mic

Your helmet type largely dictates the mic choice, but here’s a quick comparison:

  • Boom mic: Better for full-face helmets with a deep chin bar. It offers adjustable positioning and usually picks up your voice more clearly because it’s closer to your mouth. Downside: can be in the way when eating or drinking, and may break if bent repeatedly.
  • Wired mic: Better for open-face, half, and modular helmets. It’s smaller, less obtrusive, and easier to hide. Downside: placement is fixed once stuck, and it may pick up more wind noise if not positioned well.
  • Hybrid: Some Cardo models (like the Packtalk Edge) include both mics in the box, so you can switch based on your helmet. That’s the best option if you own multiple helmets.

Cost and Upgrade Considerations

Upgrading speakers or replacing a mic is relatively inexpensive. Cardo sells replacement speakers and mics as accessories, and third-party options exist, but stick to Cardo-branded parts for guaranteed compatibility. If you’re buying a new Cardo system, check which speakers are included – many current models come with 40mm JBL, but the 45mm upgrade is worth it if your helmet fits them. Also, consider the main unit’s audio output: some older models may not drive larger speakers to their full potential.

Safety and Comfort Tips

Comfort is safety. If your head hurts from speaker pressure, you’ll be distracted. Always test the fit with your helmet on for at least 15 minutes before a long ride. Make sure the mic doesn’t obstruct your vision or breathing. And never modify the helmet’s EPS foam in a way that compromises its protective integrity – if you’re unsure, consult the helmet manufacturer or a professional. Also, keep the volume at a level where you can still hear traffic and emergency vehicles; many jurisdictions have laws about maximum headphone volume while riding.

Frequently Asked Questions

Can I use any speaker with my Cardo?

No, you should use Cardo-branded speakers (or those explicitly designed for Cardo) because the connector and impedance are specific. Third-party speakers may fit physically but could have wrong impedance, leading to poor sound or damage to the amplifier.

How do I know if my helmet has speaker pockets?

Most full-face and modular helmets from major brands (Shoei, Arai, Schuberth, etc.) have pre-cut recesses in the EPS liner near the ears. You can feel them as shallow depressions. If your helmet doesn’t, you may need to cut them yourself or use the velcro mounting.

Why does my Cardo mic sound muffled?

Usually because the mic is too close to your mouth or covered by fabric. Adjust the position so it’s 1-2 cm away, and make sure the windscreen is not clogged. Also check that the mic is not pressed against the chin bar, which can cause vibration.

Can I mount the Cardo on a modular helmet?

Yes, but be careful: the clamp may interfere with the chin bar rotation. Use the thinnest clamp and test the mechanism. Some modular helmets have a recessed area for the clamp. Also, the boom mic may not work well if the chin bar flips up – use the wired mic instead.

What if my speakers are too quiet?

First, check the volume on the Cardo and your phone. Then, make sure the speakers are seated correctly and not blocked by the liner. If they’re still quiet, you may need the 45mm upgrade or a helmet with better acoustics. Also, earplugs can actually improve clarity by reducing wind noise – many riders find that with earplugs, the audio sounds clearer.

How do I clean the mic and speakers?

Use a soft, dry cloth to wipe the speaker grilles. For the mic, gently remove the windscreen and rinse it with water, then let it dry completely before reattaching. Avoid using liquids directly on the mic capsule.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →