keepcalculator

06 Numbers and Powers

Complex Furnishings Codes: What They Mean

Card No. 06·85091 · Updated · Standard formula, shown below

Pass/fail index 1.75
Time to ignition (seconds)
12 s
You entered
Flame height (mm)
30 mm
You entered
You enter
Time to ignition (seconds), Flame height (mm)
You get
Pass/fail index
Rounding
2 dp

Complex furnishings codes are the classification numbers that identify the fire-resistance and performance characteristics of upholstered furniture and mattresses, primarily used in the United States to meet California Technical Bulletin 117-2013 and similar regulations. When you see a label with a code like “CA TB117-2013” or a series of letters and numbers, it tells you whether the product passed open-flame and smolder tests, and what materials were used. This article explains what these codes mean, how to read them, and what they do and do not guarantee.

Formula

The calculator above gives a rough pass/fail index based on two common test measurements: time to ignition and flame height. The formula is:

Index = (Time to ignition / 12) + (Flame height / 40)

  • t = time to ignition in seconds (higher is better)
  • f = flame height in millimeters (lower is better)

A lower index indicates better performance. The threshold of 1.0 is arbitrary; actual regulations use specific pass/fail criteria, not a single index.

Worked Example

Using the defaults: t = 12 seconds, f = 30 mm.

Index = (12 / 12) + (30 / 40) = 1 + 0.75 = 1.75

This means the material takes 12 seconds to ignite and produces a 30 mm flame, giving an index of 1.75. In a real test, both values would need to meet specific limits set by the regulation.

Background: Why Furnishings Codes Exist

Furnishings codes originated from California’s Technical Bulletin 117 (TB117), first issued in 1975, which required upholstered furniture to resist open-flame ignition. The original test was a severe open-flame test that led manufacturers to use flame-retardant chemicals, some of which raised health concerns. In 2013, California updated to TB117-2013, which replaced the open-flame requirement with a smolder test (cigarette ignition). This change reduced the need for chemical flame retardants and aligned with federal standards. Other states and the federal government have since adopted similar smolder-based standards, but TB117-2013 remains the most recognized code.

How to Read a Furnishings Code Label

Most upholstered furniture sold in the U.S. carries a permanent label with a code. Here’s what you’ll typically see:

  • CA TB117-2013: Indicates compliance with California’s smolder test.
  • UFAC: Upholstered Furniture Action Council label, showing voluntary compliance with smolder resistance.
  • Mattress codes: Federal standard 16 CFR 1632 (open flame) and 1633 (smolder) for mattresses.
  • Filling material codes: Letters like “P” for polyurethane foam, “F” for fiber, “C” for cotton, etc.

The label often includes a manufacturing date and a statement like “This article meets the requirements of California Technical Bulletin 117-2013.” Codes may also appear as a series of letters and numbers that identify the foam density, firmness, and flame retardant type, but these are not standardized across manufacturers.

Common Misconceptions

A frequent misunderstanding is that a furnishings code guarantees the furniture will not catch fire. No code means fireproof; it only indicates that the item passed a specific test under controlled conditions. Another misconception is that all codes require flame retardants. TB117-2013 specifically allows manufacturers to meet the smolder test without chemical flame retardants, and many do. Also, a code from California is not a federal requirement, but because California is a large market, most manufacturers comply nationwide.

How to Choose Furniture Based on Codes

When buying furniture, look for the label and check for TB117-2013 or UFAC. If you have concerns about chemical flame retardants, choose products labeled as “no added flame retardants” or those that meet the smolder test without them. For mattresses, ensure they meet the federal standard (16 CFR 1633). For commercial or public spaces, local fire codes may require specific ratings, so check with your local authority. Always keep the label for future reference, as it may be needed for warranty or compliance verification.

Common Problems and Limitations

One issue is that older furniture may still have pre-2013 labels, which indicate open-flame resistance but may contain more flame retardants. Another problem is that labels can be incomplete or ambiguous, especially on imported furniture. The biggest limitation of TB117-2013 is that it only tests smolder resistance, not open flames. A couch that passes the smolder test can still burn rapidly in a real fire. Also, the test uses a standard cigarette, but actual cigarettes may differ. Finally, the code does not cover all materials—some fabrics are tested as part of the composite, but the label may not specify which component was tested.

Cost and Safety Considerations

Furniture that meets higher fire standards may cost slightly more due to the use of inherently smolder-resistant materials like wool or treated fabrics. However, the price difference is often small, and many manufacturers meet the standard without significant cost increases. For safety, always maintain smoke detectors and have an escape plan. The code is a minimum baseline, not a guarantee of safety. If you have children or vulnerable adults, consider additional precautions like flame-resistant covers (if they meet safety standards) and keeping furniture away from open flames.

Alternatives and the Future

Some manufacturers are moving to inherently fire-resistant materials like wool, modacrylic, or treated cotton, which do not require chemical additives. Others are using barrier fabrics that prevent smoldering. There is also a trend toward more transparent labeling, with some brands voluntarily disclosing all materials. Internationally, codes like the UK’s Furniture and Furnishings (Fire) (Safety) Regulations 1988 require both smolder and open-flame tests, which are stricter than U.S. standards. As consumer awareness grows, we may see a move toward more comprehensive, health-conscious standards.

Frequently Asked Questions

Does a TB117-2013 label mean the furniture is flame retardant?

Not necessarily. TB117-2013 only requires resistance to smoldering cigarettes. Many manufacturers meet this without using chemical flame retardants, using instead denser foams or barrier fabrics. The label does not specify whether flame retardants were used.

Is it safe to buy furniture with a pre-2013 label?

Pre-2013 labels indicate the item passed an open-flame test, which often required flame retardants. While it may be more fire-resistant, it may also contain chemicals that some people prefer to avoid. The furniture is not unsafe, but you may want to consider the trade-off.

Do these codes apply to all types of furniture?

TB117-2013 applies to upholstered furniture (sofas, chairs, etc.) sold in California. Mattresses have separate federal standards. Other items like pillows, cushions, and outdoor furniture may not be covered, so check with the manufacturer.

How do I know if a code is genuine?

Look for a permanent label sewn into the furniture, usually under a cushion or on the frame. The label should have the exact wording “CA TB117-2013” or similar. If you suspect a counterfeit, contact the manufacturer or the California Bureau of Electronic and Appliance Repair (BEAR) for verification.

Can I remove the label?

It is illegal to remove the label in many states, and it is also not a good idea because you lose documentation of compliance. Keep the label intact for warranty and resale purposes.

Does the code affect furniture flammability in real life?

The smolder test is a good indicator of resistance to cigarette ignition, which is the most common cause of furniture fires. However, it does not predict behavior in an open flame. Always practice fire safety, regardless of the label.

Related

Formula used
in t | Time to ignition (seconds) | s | 12 | 0 | 120
in f | Flame height (mm) | mm | 30 | 0 | 200
out p | Pass/fail index | - | (t / 12) + (f / 40) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →