keepcalculator

06 Numbers and Powers

Hard Coatings vs Corrosion Resistant Coatings: Which?

Card No. 06·80183 · Updated · Standard formula, shown below

Coating mass 0.78 g
Coating thickness
10 µm
You entered
Surface area
100 cm²
You entered
Coating density
7.8 g/cm³
You entered
You enter
Coating thickness, Surface area, Coating density
You get
Coating mass
Rounding
2 dp

Hard coatings and corrosion resistant coatings serve different primary purposes: hard coatings protect against wear, abrasion, and scratching, while corrosion resistant coatings protect against chemical attack and rust. The right choice depends on your application’s dominant failure mode—if parts wear out, choose a hard coating; if they rust or pit, choose a corrosion resistant coating; often, you need both.

Formula

The calculator estimates the mass of a coating applied to a flat surface. The formula is:

m = t × a × d / 10,000

Where:

  • m = coating mass (grams)
  • t = coating thickness (µm, micrometers)
  • a = surface area (cm²)
  • d = coating density (g/cm³)

The division by 10,000 converts µm·cm² to grams, since 1 µm = 0.0001 cm. This is useful for estimating material consumption or comparing coating costs per unit area.

Worked Example

Using the default values from the calculator: thickness = 10 µm, area = 100 cm², density = 7.8 g/cm³ (typical for hard chrome).

  1. Convert thickness to cm: 10 µm = 10 × 0.0001 = 0.001 cm
  2. Volume = 0.001 cm × 100 cm² = 0.1 cm³
  3. Mass = 0.1 cm³ × 7.8 g/cm³ = 0.78 g

The calculator gives 0.78 g, matching the manual calculation.

What Are Hard Coatings?

Hard coatings are thin layers (typically 1–50 µm) applied to a surface to increase its hardness and resistance to mechanical wear. Common types include:

  • Titanium nitride (TiN) – golden-colored, used on cutting tools and drill bits.
  • Chromium nitride (CrN) – silver-gray, good for forming tools and plastic molds.
  • Diamond-like carbon (DLC) – black, extremely hard and low-friction, used in automotive engine components.
  • Hard chrome plating – electroplated, thick (up to 500 µm), used on hydraulic rods and industrial rollers.
  • Aluminum oxide (Al₂O₃) – ceramic, applied by thermal spray, used in high-temperature wear applications.

Hard coatings are applied via physical vapor deposition (PVD), chemical vapor deposition (CVD), electroplating, or thermal spraying. Their primary function is to reduce friction, prevent abrasive wear, and extend component life in sliding or impact conditions.

What Are Corrosion Resistant Coatings?

Corrosion resistant coatings protect metal surfaces from chemical reactions with the environment—mainly oxidation (rusting) and electrochemical attack. They work by creating a barrier between the metal and corrosive agents like water, salt, acids, or industrial chemicals. Common types include:

  • Zinc (galvanizing) – sacrificial coating; zinc corrodes preferentially, protecting steel.
  • Epoxy and polyurethane paints – thick organic barriers, widely used on pipelines, bridges, and marine structures.
  • Powder coating – dry powder melted into a durable, decorative layer.
  • Anodizing – electrochemical conversion of aluminum to a thick oxide layer.
  • Ceramic and glass enamels – inert, non-porous layers for chemical tanks and cookware.

These coatings are typically thicker (25–500 µm) than hard coatings and are chosen based on the specific corrosive environment—saltwater, acidic fumes, or high humidity.

How to Choose: Key Factors

To decide which coating is right, ask these questions:

  1. What is the primary failure mode? If parts are failing by scratching, galling, or wear, choose a hard coating. If they are rusting, pitting, or discoloring, choose a corrosion resistant coating.
  2. What is the operating environment? High humidity, salt spray, or chemical exposure demands corrosion protection. Abrasive particles, sliding contact, or high loads demand wear protection.
  3. What is the substrate material? Steel can be galvanized or painted; aluminum can be anodized; titanium can be PVD-coated. Some coatings adhere better to certain metals.
  4. What is the operating temperature? Many organic coatings degrade above 200°C, while ceramic hard coatings can withstand 800°C+.
  5. Are there dimensional tolerances? Hard coatings are thin and precise; thick corrosion coatings may require post-machining.

In many real-world applications, you need both. For example, a marine hydraulic cylinder rod uses a hard chrome plating (wear resistance) over a steel substrate that is also protected by a paint system or cathodic protection. Similarly, automotive fasteners are often zinc-plated (corrosion) and then coated with a thin DLC layer (wear and friction).

Common Problems and Misconceptions

A common misconception is that hard coatings are automatically corrosion resistant. This is not true. For instance, titanium nitride (TiN) is hard but porous; in saltwater, it can actually accelerate corrosion of the underlying steel due to galvanic effects. Conversely, a thick epoxy coating is excellent against corrosion but offers little protection against abrasive wear—it will scratch and erode quickly.

Another issue is coating adhesion. A hard coating on a poorly prepared surface will flake off, exposing the substrate. Similarly, a corrosion coating with pinholes can trap moisture and cause localized rusting. Proper surface preparation (blasting, cleaning, etching) is critical for both types.

Also, thickness is not always better. For hard coatings, excessive thickness can lead to brittleness and cracking under load. For corrosion coatings, too thick a layer may crack due to thermal expansion differences. Follow the coating supplier’s recommended thickness range.

Cost and Practical Considerations

Hard coatings, especially PVD types, are generally more expensive per unit area than paint or powder coating. A PVD coating on a cutting tool might cost $2–$10 per piece, while galvanizing a large structural beam might cost $0.50–$1.50 per kg of steel. However, the cost must be weighed against the value of the component and its expected life extension.

For corrosion coatings, the cost varies widely: zinc plating is economical, while high-performance ceramic or fluoropolymer coatings are premium. Consider the total lifecycle cost—a cheaper coating that fails in 2 years may be more expensive than a premium coating that lasts 10 years.

Another factor is repairability. Hard coatings often require stripping and reapplication if damaged, while corrosion coatings like paint can be touched up easily. In field applications, this can be decisive.

Safety and Environmental Notes

Both coating types involve chemicals and processes that require safety precautions:

  • PVD and CVD processes use high temperatures and vacuum, with potential exposure to metal vapors and reactive gases.
  • Electroplating (chrome, zinc) uses toxic hexavalent chromium and acidic baths; proper ventilation and waste disposal are mandatory.
  • Thermal spraying produces fine metal dust and noise; respiratory protection is required.
  • Solvent-based paints and epoxies emit volatile organic compounds (VOCs); use in ventilated areas with appropriate PPE.

Always follow the coating manufacturer’s safety data sheets and local environmental regulations. For food-contact or medical applications, ensure the coating is certified for that use—for example, DLC is often food-safe, while some epoxy formulations are not.

Alternatives to Coatings

If coatings are not suitable, consider these alternatives:

  • Material substitution – Use stainless steel instead of carbon steel to avoid corrosion, or use a harder base material (e.g., tool steel) to reduce wear.
  • Surface hardening – Processes like carburizing, nitriding, or induction hardening change the substrate itself, avoiding adhesion issues.
  • Corrosion inhibitors – Add chemicals to the environment (e.g., in cooling water) to reduce corrosivity.
  • Design changes – Avoid crevices, sharp edges, or galvanic couples to minimize corrosion without any coating.

These alternatives may be more cost-effective in the long run, especially for high-volume or high-stress applications.

Frequently Asked Questions

Can I apply a hard coating over a corrosion resistant coating?

Yes, but only if the corrosion coating is compatible with the hard coating process. For example, you can apply a DLC hard coating over a zinc-plated surface, but the zinc layer must be thin and smooth. However, most PVD processes require a clean, vacuum-compatible surface, which many organic coatings cannot provide. In practice, it’s easier to apply a corrosion resistant topcoat over a hard coating, but the hard coating may not provide enough adhesion for the topcoat.

Which coating is better for outdoor steel structures?

For outdoor steel structures like bridges or fences, corrosion resistant coatings are the primary choice—typically hot-dip galvanizing or a multi-layer paint system. Hard coatings are not necessary because the main threat is rust, not abrasion. However, if the structure also experiences mechanical wear (e.g., a sliding gate), you might add a hard coating on the wear surfaces.

How do I know if a coating is hard enough?

Hardness is measured by microindentation (e.g., Vickers or Knoop). Typical values: TiN ~2300 HV, DLC ~1500–3000 HV, hard chrome ~800–1000 HV. Compare these to your application’s abrasive particles or mating surface hardness. If the coating is softer than the abrasive, it will wear quickly. For most industrial wear, a hardness above 1500 HV is considered good.

What is the difference between anodizing and hard anodizing?

Anodizing is an electrochemical process that creates a porous aluminum oxide layer, which can be dyed. Hard anodizing (Type III) uses a higher voltage and lower temperature to produce a thicker, denser, and harder layer (up to 100 µm, hardness ~400 HV). Hard anodizing provides both wear and corrosion resistance, but it’s thicker and changes dimensions more. Regular anodizing is mainly for corrosion protection and aesthetics.

Can I use a corrosion resistant coating on a wear surface?

Generally, no. Most corrosion coatings (paint, zinc, epoxy) are soft and will be quickly worn away by friction or abrasion. If you need both properties, consider a duplex system: a hard coating for wear plus a corrosion resistant primer underneath, or a ceramic coating that provides both (e.g., aluminum oxide thermal spray).

How do I test coating quality?

Common tests include: salt spray test (ASTM B117) for corrosion resistance, Taber abrasion test for wear resistance, cross-cut adhesion test, and thickness measurement with a magnetic or eddy-current gauge. For critical applications, perform these tests on sample coupons before full production.

Related

Formula used
in t | Coating thickness | µm | 10 | 0.5 | 5000
in a | Surface area | cm² | 100 | 1 | 1000000
in d | Coating density | g/cm³ | 7.8 | 0.5 | 20
out m | Coating mass | g | t * a * d / 10000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →