keepcalculator

06 Numbers and Powers

How to Choose Rare Earth Magnets for Motors, Sensors & Speakers

Card No. 06·70437 · Updated · Standard formula, shown below

Choosing the right rare earth magnet for a motor, sensor, or speaker means matching its magnetic strength, size, shape, and temperature rating to your specific application. This guide walks you through the key specifications—grade, dimensions, coating, and magnetization direction—so you can select a magnet that performs reliably without overpaying for strength you don’t need.

What You’ll Need

  • Your application’s operating temperature range (minimum and maximum)
  • Available space for the magnet (length, width, height, or diameter)
  • Required magnetic force or field strength (if known from a prototype or spec)
  • Environment details: humidity, chemicals, or physical shock exposure
  • Magnet supplier datasheets (or access to online magnet specifications)

Step-by-Step

  1. Define the application’s role. Motors need magnets that produce torque efficiently; sensors often require a stable magnetic field for Hall-effect or reed switches; speakers need magnets that drive a voice coil with controlled force. Write down the primary function—this determines the magnet’s shape and magnetization pattern.
  2. Determine the temperature range. Rare earth magnets lose strength as they heat up, and can permanently demagnetize if they exceed their maximum operating temperature. For example, N42 neodymium magnets are rated up to 80°C (176°F), while N42SH can handle up to 150°C (302°F). If your motor runs hot, choose a grade with an ‘H’, ‘SH’, or ‘UH’ suffix.
  3. Choose the magnet material. Neodymium (NdFeB) is the strongest and most common for compact devices. Samarium cobalt (SmCo) is more expensive but works at higher temperatures (up to 300°C) and is more corrosion-resistant. For most consumer electronics, neodymium is the right choice; for aerospace or high-heat industrial, consider SmCo.
  4. Select the grade (strength). The grade number (N35, N42, N52, etc.) indicates the maximum energy product—higher numbers mean stronger magnets. For sensors, a lower grade like N35 may suffice; for motors and speakers that need strong force in a small size, N42 or N45 is common. N52 is the strongest, but it’s brittle and more expensive.
  5. Pick the shape and dimensions. Motors often use arc segments (for brushless motors) or discs (for small DC motors). Sensors typically use small discs, blocks, or rings. Speakers use discs, rings, or bar magnets. Measure the available cavity and choose a magnet that fits with a small tolerance (usually 0.1-0.5mm clearance).
  6. Determine the magnetization direction. Magnets can be magnetized through thickness, diameter, or length. For motors, you often need radial magnetization (for arc magnets) or axial (for discs). For sensors, axial magnetization is common. Check the supplier’s diagram—this is critical for proper function.
  7. Choose a coating. Neodymium magnets are prone to corrosion. Common coatings are nickel (standard, good for indoor use), epoxy (better in humid environments), and gold or zinc (for special needs). If the magnet is inside a sealed motor, nickel is fine. For sensors exposed to moisture, choose epoxy or parylene.
  8. Check mechanical tolerances. For motors, the magnet must fit precisely in the rotor or stator. Specify tolerances (e.g., +0.05mm) if needed. For speakers, the magnet often sits in a magnetic circuit with a pole piece—tight tolerances ensure consistent air gap.
  9. Consider assembly and handling. Rare earth magnets are brittle and can chip. If you’re assembling by hand, choose a magnet with a protective coating and consider using spacers during shipping. For automated assembly, specify a chamfer or rounded edges if possible.
  10. Order a sample and test. Before committing to a large batch, order 5-10 samples from the supplier. Test them in your actual device to verify force, temperature behavior, and fit. Measure the magnetic field at the working distance using a gaussmeter if possible.

Common Mistakes

  • Ignoring temperature derating: A magnet that works at room temperature may fail in a motor that runs at 80°C. Always check the max operating temperature.
  • Choosing too high a grade: N52 magnets are strong but brittle and harder to handle. For many applications, N42 is sufficient and more cost-effective.
  • Forgetting the coating: Bare neodymium magnets rust quickly in humid air. Always specify a coating unless it’s inside a sealed, dry enclosure.
  • Wrong magnetization direction: Ordering a disc magnet magnetized through diameter when you need axial magnetization is a common error. Double-check the supplier’s spec sheet.
  • Assuming all magnets of the same grade are identical: Different manufacturers have slightly different properties. Stick with reputable suppliers and verify with a gaussmeter.

Tips

  • For motors, consider using a magnet with a higher coercivity (Hcj) if you plan to run at high speeds—this prevents demagnetization from opposing fields.
  • In sensors, a smaller magnet with a higher grade can provide a more focused field, which may improve sensitivity.
  • For speakers, the magnet’s strength affects efficiency and bass response. A stronger magnet generally gives tighter control, but too strong can cause distortion—match it to the voice coil’s impedance.
  • If you’re unsure about the exact size, order a few different dimensions and test them. Magnets are inexpensive in small quantities.
  • Use a steel keeper (a piece of iron) to short-circuit the magnet during storage to prevent accidental attraction and demagnetization.

Troubleshooting

  • Magnet is too weak: Check if you’re operating above the temperature rating. If so, switch to a higher temperature grade (e.g., N42SH). Also verify you’re measuring at the correct distance—field strength drops rapidly with distance.
  • Magnet chips or cracks during assembly: Use a magnet with a thicker coating, or request a chamfer. Also, handle magnets carefully—they can snap together and break.
  • Magnet demagnetizes over time: This usually indicates the operating temperature exceeds the magnet’s rating, or there’s an opposing magnetic field (like from a motor’s stator). Choose a higher coercivity grade.
  • Magnet rusts: If the coating is damaged, the magnet will corrode. Use epoxy-coated magnets for humid environments, and avoid scratching the surface.
  • Magnet doesn’t fit: Re-measure the cavity. Remember that magnet dimensions often have tolerances of ±0.05mm. If it’s too tight, order a smaller size or request a tighter tolerance.

Frequently Asked Questions

What is the difference between N35 and N52 magnets?

The number indicates the maximum energy product (in MGOe). N52 is about 50% stronger than N35, but it’s also more brittle and expensive. For most applications, N42 or N45 offers a good balance.

Can I use a neodymium magnet in a speaker?

Yes, neodymium is commonly used in modern speakers because it’s strong and lightweight. You just need to ensure the magnet’s size and strength match the voice coil and basket design.

How do I know if a magnet is magnetized through thickness or diameter?

Check the supplier’s datasheet—it will have a diagram showing the magnetization direction. If you don’t have one, test with a compass or a small piece of steel: the poles are on the faces where the steel sticks strongest.

What does the ‘SH’ in N42SH mean?

‘SH’ stands for ‘super high’ temperature rating. N42SH can operate up to 150°C, while standard N42 is only rated to 80°C. The letters indicate the maximum operating temperature.

Can I cut a rare earth magnet to size?

Cutting or drilling neodymium magnets is difficult and dangerous—they are brittle and can shatter, and the dust is flammable. Always order the exact size you need.

How do I store rare earth magnets safely?

Keep them in a steel container or with a steel keeper across the poles to short the magnetic field. Store them away from electronic devices and pacemakers. Also, keep them separated to avoid chipping.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →