Spin Only Cycle on Samsung Washer: Step-by-Step

Running a spin-only cycle on your Samsung washer is a quick way to remove excess water from clothes without a full wash, which is handy for bulky items like towels, jeans, or delicates that you want to dry faster. This guide walks you through the exact button presses and dial settings to get the machine spinning in under a minute, plus what to do if it won’t cooperate.

What You’ll Need

• A Samsung front-load or top-load washer (models from roughly 2015 onward, but the steps apply to most current ones)
• Access to the control panel (no tools needed)
• Clothes or items you want to spin (optional, but the machine needs a load to balance)
• Your washer’s manual (helpful if your model has a different dial layout, but not required)

Step-by-Step

1. Turn on the washer. Press the Power button. The display will light up, and the machine will be ready for input.
2. Open the door (front-load) or lid (top-load). Make sure the drum is empty or has the items you want to spin. Do not overload; the machine needs room to balance the load.
3. Select the Spin cycle. Look for a cycle dial or a series of cycle buttons. On most Samsung models, you’ll find a Spin or Spin Only option. If your model has a dial, turn it to the Spin position (often near the end of the cycle list, sometimes labeled with a water drop or spiral icon). If you have a button-based panel, press the Cycle or Menu button until Spin appears on the display.
4. Adjust spin speed (optional). If your model has a Spin Speed button, you can choose a lower speed for delicate items (e.g., 400 or 600 RPM) or a higher speed for sturdy fabrics (up to 1400 RPM). The default is usually fine for mixed loads.
5. Press Start/Pause. The washer will begin the spin cycle. It will first drain any remaining water, then spin the drum at the selected speed. A typical spin-only cycle lasts 5 to 15 minutes, depending on the model and speed.
6. Wait for the cycle to finish. The display will count down. When it reaches zero, the door will unlock (on front-loaders) or the lid will release (on top-loaders). Remove your items immediately to prevent wrinkles.
7. Turn off the washer. Press Power to shut it down completely, or leave it on for the next load.

Common Mistakes

• Skipping the drain step: If your washer has leftover water in the drum, it will drain first. Don’t panic if you hear water running before the spin starts—that’s normal.
• Overloading: Cramming too many items can cause the washer to detect an unbalanced load and stop spinning. Always leave space for items to move freely.
• Selecting a full wash cycle instead: Double-check that you’ve chosen the Spin cycle, not Normal or Heavy Duty. A full cycle will add water and detergent, which defeats the purpose.
• Ignoring the child lock: If the control panel doesn’t respond, the child lock may be on. Press and hold the Child Lock button (usually for 3 seconds) to disable it.

Tips

• Use the spin-only cycle for quick drying: After hand-washing delicates, a low-speed spin (400–600 RPM) removes water without damaging fabrics.
• Balance the load: For best results, include a few items of similar size and weight. A single heavy towel can cause the drum to spin unevenly.
• Clean the door seal: After spinning, wipe the rubber gasket on front-loaders to prevent mold and odor.
• Check the drain hose: If the spin cycle takes too long, ensure the drain hose isn’t kinked or clogged, which can slow water removal.
• Use the delay start feature (if available): You can set the spin cycle to run later, but it’s rarely needed—spin is quick.

Troubleshooting

Washer won’t start spinning:

• Ensure the door/lid is fully closed and latched. Most Samsung washers won’t spin if the door isn’t secure.
• Check if the machine is in pause mode. Press Start/Pause again to resume.
• If the display shows an error code (e.g., UE for unbalanced), redistribute the load and try again.

Spin cycle stops mid-way:

• This usually indicates an unbalanced load. Open the door, rearrange the items, and restart the cycle.
• If the machine is vibrating excessively, it may be on an uneven floor. Adjust the leveling feet.

No water drains:

• Check the drain filter (usually at the bottom front of the washer) for clogs. Clean it if necessary.
• Inspect the drain hose for kinks or blockages.

Cycle finishes but clothes are still wet:

• Increase the spin speed if your model allows it.
• Reduce the load size—overloading prevents effective spinning.

Frequently Asked Questions

Can I run a spin-only cycle on any Samsung washer?

Yes, most Samsung washers have a dedicated Spin cycle. If you don’t see it on the dial, check the manual—some models require you to select a wash cycle and then press Spin Only as an option.

How long does a spin-only cycle take?

Typically 5 to 15 minutes, depending on the model and spin speed. Higher speeds may take slightly longer for the machine to ramp up and down.

Can I spin just one item?

Yes, but a single heavy item (like a towel) may cause imbalance. Add a few lighter items to balance the load.

Will a spin-only cycle damage my clothes?

No, if you use the appropriate speed. Delicates should be spun at low speed (400–600 RPM). High speeds are fine for sturdy fabrics like jeans and towels.

Do I need to add detergent?

No, the spin-only cycle uses no water and no detergent. It only removes water from already-washed items.

Why does my washer show an error during spin?

The most common error is UE (unbalanced). Redistribute the load and restart. Other errors like dE (door open) mean the door isn’t closed properly.

Related

• Is an Intel Core i3 Good Enough for Zoom?
• Turn Off Google Recording: Step-by-Step Guide
• Sony Adaptive Controller Buttons That Transform