keepcalculator

06 Numbers and Powers

MM vs MC Phono Stages: Which Cartridge Input Do You Need?

Card No. 06·78654 · Updated · Standard formula, shown below

Preamp output (V) 0.50 V
Gain (dB)
40 dB
You entered
Cartridge output (mV)
5 mV
You entered
You enter
Gain (dB), Cartridge output (mV)
You get
Preamp output (V)
Rounding
2 dp

Choosing between a moving magnet (MM) and moving coil (MC) phono stage input comes down to one simple rule: match the input to your cartridge type. If your turntable has a moving magnet cartridge, you need an MM phono stage; if it has a moving coil cartridge, you need an MC phono stage. This article explains the technical differences, how to identify your cartridge, and what to consider when buying a phono preamp.

Formula

The output voltage of a phono stage is calculated as:

Vout = Vcart × 10(Gain/20)

Where:

  • Vout = preamp output voltage in volts (V)
  • Vcart = cartridge output voltage in millivolts (mV)
  • Gain = phono stage gain in decibels (dB)

This formula shows how much the phono stage amplifies the tiny cartridge signal to line level (typically 0.2–2 V).

Worked Example

Using the default values from the calculator (gain = 40 dB, cartridge output = 5 mV):

  1. Convert cartridge output to volts: 5 mV ÷ 1000 = 0.005 V
  2. Calculate the gain factor: 10(40/20) = 102 = 100
  3. Multiply: 0.005 V × 100 = 0.5 V

The phono stage outputs 0.5 V, a typical line-level signal.

What Is a Phono Stage?

A phono stage (or phono preamp) is a small amplifier that boosts the very low signal from a turntable cartridge to the same level as other audio sources (like a CD player or streamer). It also applies the RIAA equalization curve, which restores the bass and treble balance that was intentionally altered during record cutting. Without a phono stage, a turntable sounds extremely quiet and thin through a standard amplifier.

Phono stages are built into many integrated amplifiers, receivers, and some turntables, but dedicated external units often offer better performance and more flexibility. The two main types of phono stages correspond to the two main types of cartridge: MM and MC.

Moving Magnet (MM) Cartridges

Moving magnet cartridges are the most common and affordable type. In an MM cartridge, the stylus is attached to a magnet that moves between fixed coils. The movement of the magnet induces a small voltage in the coils. Typical MM output is 3–6 mV, which is relatively high, so the phono stage only needs moderate gain (around 40 dB). MM cartridges are easy to install, have replaceable styluses, and are compatible with virtually any phono input.

Because of their higher output, MM cartridges are less sensitive to noise and hum. They are a great choice for beginners and for anyone who wants a reliable, low-maintenance setup.

Moving Coil (MC) Cartridges

Moving coil cartridges are usually found on higher-end turntables. In an MC cartridge, the coils themselves are attached to the stylus and move between fixed magnets. This design is more precise and can track record grooves more accurately, but it produces a much smaller voltage—typically 0.2–0.5 mV. That’s about ten times less than an MM cartridge, so an MC phono stage needs much higher gain (around 60 dB or more).

MC cartridges are further divided into high-output and low-output types. High-output MC cartridges (around 1–2 mV) can sometimes work with an MM input, but they are rare. Low-output MC cartridges require a dedicated MC phono stage or a step-up transformer. MC cartridges also have non-replaceable styluses—when the stylus wears out, the entire cartridge must be replaced, which is more expensive.

How to Identify Your Cartridge Type

Before choosing a phono stage, you must know what cartridge you have. Here are the most reliable ways to check:

  • Look at the cartridge body: The model name is usually printed on the top or side. Search the model online to find its specifications.
  • Check the turntable manual: The manual will list the cartridge type and output voltage.
  • Measure the output: If you have a multimeter, you can measure the DC resistance across the cartridge pins. MM cartridges typically have 400–1,000 ohms; MC cartridges have 3–50 ohms.
  • Listen for volume: If the volume is very low even with the phono input selected, it might be an MC cartridge being fed into an MM-only input.

If you still can’t tell, ask a local audio dealer or check online forums with a photo of the cartridge.

MM vs MC: Key Differences

The table below summarizes the main differences between MM and MC cartridges:

  • Output voltage: MM 3–6 mV; MC 0.2–0.5 mV (low-output)
  • Required gain: MM ~40 dB; MC ~60 dB
  • Stylus replacement: MM replaceable; MC not replaceable
  • Cost: MM generally cheaper; MC often more expensive
  • Sound quality: MC can offer more detail and lower distortion, but depends on the system
  • Compatibility: MM works with any phono input; MC needs a dedicated MC stage or step-up transformer

In practice, most listeners will be perfectly happy with an MM cartridge. MC is for those seeking the last bit of fidelity and are willing to pay for it.

Choosing the Right Phono Stage

When shopping for a phono stage, consider these factors:

  • Cartridge type: Make sure the phono stage has the correct input (MM, MC, or both).
  • Gain switch: Some phono stages let you adjust gain to match your cartridge output. This is useful if you might upgrade later.
  • Loading options: MC cartridges require specific input impedance (usually 100 ohms) and capacitance settings. Adjustable loading helps fine-tune the sound.
  • Built-in vs external: A built-in phono stage in an amplifier is often adequate, but an external one can reduce interference and offer better components.
  • Budget: There are good MM phono stages at low prices, but MC-capable stages cost more due to the extra gain and precision required.

If your amplifier has a phono input, check whether it is MM or MC. Many budget amplifiers only have MM. If you have an MC cartridge, you’ll need an external MC phono stage or step-up transformer.

Common Problems and Misconceptions

One common mistake is assuming that all phono inputs are the same. Plugging an MC cartridge into an MM input will produce very low volume and may require you to turn the volume up to maximum, which also amplifies noise. Conversely, plugging an MM cartridge into an MC input (if the MC input has enough gain) can cause distortion and clipping because the signal is too strong.

Another misconception is that MC cartridges are always “better” than MM. While MC designs can have lower moving mass and better tracking, the cartridge’s quality and the rest of the system matter more. A high-quality MM cartridge can outperform a cheap MC cartridge.

Also, some phono stages have a switch for MM/MC, but the MC setting might not provide enough gain for very low-output MC cartridges. Check the gain specifications: low-output MC cartridges need at least 60 dB, ideally 65–70 dB.

Frequently Asked Questions

Can I use an MC cartridge with an MM phono input?

Technically yes, but the sound will be very quiet. You’ll need to crank the volume, which also amplifies background hiss. It’s not recommended unless you have a high-output MC cartridge (above 1 mV) and your phono stage has enough gain.

What is a step-up transformer?

A step-up transformer is a device that boosts the low output of an MC cartridge to a level that an MM phono stage can handle. It’s an alternative to a dedicated MC phono stage. Step-up transformers are passive and can sound very good, but they are often expensive and require careful matching with the cartridge’s impedance.

How do I know if my turntable has a built-in phono stage?

Check the back of the turntable for a switch labeled “Phono” or “Line.” If it has a “Line” output, it has a built-in phono stage. If it only has “Phono” output, you need an external phono stage or an amplifier with a phono input.

What is the difference between high-output and low-output MC cartridges?

High-output MC cartridges produce around 1–2 mV and can often be used with an MM input. Low-output MC cartridges produce 0.2–0.5 mV and require a dedicated MC phono stage with high gain. High-output MCs are less common and often considered a compromise between MM and low-output MC.

Does the phono stage affect sound quality?

Yes, significantly. The phono stage is responsible for the RIAA equalization and amplification. A poor phono stage can add noise, distort the frequency response, and reduce channel separation. A good phono stage can reveal more detail and dynamics from the same cartridge.

Can I upgrade from MM to MC later?

Yes, but you’ll need to ensure your phono stage supports MC or purchase a separate MC phono stage. Some phono stages have both MM and MC inputs, so you can switch without buying new equipment. If your amplifier only has MM, you’ll need an external MC phono stage or step-up transformer.

Related

Formula used
in gain | Gain (dB) | dB | 40 | 0 | 70
in voltage | Cartridge output (mV) | mV | 5 | 0.1 | 10
out output | Preamp output (V) | V | voltage / 1000 * 10^(gain/20) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →