keepcalculator

06 Numbers and Powers

Recover Data from Broken RAID: What Works

Card No. 06·76508 · Updated · Standard formula, shown below

Yes, you can often recover data from a broken RAID array, but the success rate depends on the type of failure, the RAID level, and what you do immediately after the failure. The first rule is: do not rebuild, reinitialize, or run any recovery software on the array itself until you have a plan, because those actions can overwrite the very data you are trying to save.

How RAID Works and Why It Breaks

RAID (Redundant Array of Independent Disks) combines multiple physical drives into one logical unit to improve performance, redundancy, or both. The most common levels are:

  • RAID 0 (striping): Data is split across all drives with no redundancy. If one drive fails, the whole array is lost.
  • RAID 1 (mirroring): Data is duplicated on two or more drives. A single drive failure still leaves a working copy.
  • RAID 5 (striping with parity): Data and parity are distributed across all drives. One drive can fail without data loss.
  • RAID 6 (dual parity): Similar to RAID 5 but tolerates two simultaneous drive failures.
  • RAID 10 (mirror + stripe): Combines mirroring and striping; usually tolerates one drive failure per mirror pair.

An array “breaks” when one or more drives fail, drop out of the array, or when the RAID controller or software loses its configuration. The failure can be physical (bad sectors, head crash, electronic failure) or logical (corrupted metadata, accidental deletion, power loss during write).

Immediate Steps to Take After a RAID Failure

  1. Stop using the array. Do not reboot the system, do not run chkdsk or fsck, and do not attempt to “repair” the array from the RAID BIOS.
  2. Label each drive by its slot position and cable connection before removing anything. This preserves the original order, which is critical for reconstruction.
  3. Image each drive to a separate healthy disk using a tool like ddrescue (Linux) or a commercial imaging utility. Work on the images, not the originals.
  4. Identify the RAID parameters: level, stripe size, parity rotation algorithm, and the order of the drives. This information is stored on the controller or in the drive metadata and can often be read by recovery software.
  5. Attempt recovery using dedicated RAID recovery software or a professional data recovery service if the data is valuable.

Software Recovery Options

Several software tools can reconstruct a RAID array from drive images, even if the controller is dead or the array is not recognized by the OS. These tools work by analyzing the data patterns on each disk to determine the stripe size, parity layout, and drive order.

  • R-Studio (Windows/Mac/Linux) – supports all major RAID levels, can work with drive images, and has a network edition for remote recovery.
  • ReclaiMe Free RAID Recovery (Windows) – free for arrays up to 1 TB, automatic parameter detection.
  • UFS Explorer RAID Recovery (Windows/Linux/macOS) – handles complex RAID configurations, including nested and custom levels.
  • DMDE (Windows/Linux/macOS) – low-cost, powerful, can rebuild RAID from images.

These tools generally require you to provide the individual drive images or connect the drives to a PC that can read them individually. They then reconstruct the virtual RAID volume and allow you to copy files off it. The process can take hours or days depending on drive size and speed.

When to Call a Professional Data Recovery Service

If the drives have physical damage (clicking sounds, burning smell, not spinning up), or if the data is worth more than the cost of professional recovery (often $500–$3,000+), stop all DIY attempts. Opening a drive in a non-cleanroom environment can destroy the platters. Professional services have cleanrooms, specialized tools, and experience with RAID controllers.

They can also handle cases where the controller has failed, the RAID metadata is corrupted, or multiple drives have failed. They typically charge a flat fee plus per-drive costs, and you only pay if they succeed (many offer free evaluation).

Common Mistakes That Ruin Recovery Chances

  • Rebuilding the array – When the controller asks you to rebuild, it writes new parity data across all drives, overwriting the very data you need.
  • Running filesystem repair tools – chkdsk or fsck can make logical damage worse by “fixing” structures that are actually intact.
  • Using the wrong drive order – Even if you have the correct images, assembling them in the wrong sequence yields garbage.
  • Forgetting about the OS drive – The RAID metadata may be stored on the system drive, not on the array drives.
  • Ignoring the “degraded” state – If one drive fails but the array still works, treat it as an emergency. Replace the failed drive immediately and back up.

Cost and Time Expectations

DIY software recovery costs from $0 (free trials) to about $80 for a full license. The time depends on the size of the drives and the speed of your computer; a 4 TB array can take 12–48 hours to image and reconstruct. Professional recovery typically costs $500–$2,500 for a single drive, and more for multiple drives or complex RAID levels. Turnaround is usually 3–10 business days, though expedited service may cost extra.

If the data is not critical, a DIY attempt is reasonable. If it is business-critical or irreplaceable, the cost of professional recovery is often justified.

Frequently Asked Questions

Can I recover data from a RAID 0 array with one failed drive?

Yes, if the failed drive is still readable (e.g., logical failure, bad sectors) you can image it and reconstruct the array with software. If the drive is physically dead, recovery becomes much harder and may require professional help, but it is sometimes still possible by replacing the controller board or using a donor drive.

What if the RAID controller is dead?

You don’t need the original controller if you have the drives. Recovery software can analyze the raw data to determine the RAID parameters. However, if the controller used a proprietary metadata format, you may need to emulate it or use a service that supports that specific controller.

Should I use the RAID controller’s own rebuild function?

No, not if you want to recover data from a broken array. Rebuilding writes new data across the array and can overwrite the remaining original data. Only use rebuild if you have a full backup and want to restore the array to working order.

How do I know the correct drive order for my RAID 5 array?

Recovery software can often auto-detect the order by analyzing the data and parity patterns. If not, you can try different permutations and check the filesystem structure. The drive order is also often printed on the drive labels or in the RAID BIOS configuration.

Is it safe to run recovery software on the original drives?

It is safer to create images first and run recovery on the images. Running software directly on the original drives risks further damage if the software writes to them. Always work on copies when possible.

Can I recover data after a RAID 5 array has two failed drives?

It depends. If the two failures are on different parity groups and you have a backup, you might be able to reconstruct using the remaining drives and the parity information. In practice, this is very difficult and often requires professional help. If the array is RAID 6, it can tolerate two failures by design.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →