keepcalculator

06 Numbers and Powers

ipconfig Command on Mac: How to Run It

Card No. 06·74594 · Updated · Standard formula, shown below

The short answer: the ipconfig command does exist on macOS, but it works differently than on Windows. On a Mac, you use ipconfig mainly to renew or release the DHCP lease, and you use ifconfig or ip to view your IP address and network details.

Why the Confusion?

Windows users are used to typing ipconfig to see their IP address, subnet mask, and default gateway. When they switch to a Mac, they often type the same command and get an error or a short list of options that doesn’t look familiar. That’s because macOS has its own set of network commands. The ipconfig binary on macOS is a thin wrapper around the configd system, and it only supports a few subcommands: getifaddr, getoption, getpacket, set, setifaddr, and waitfor. It does not show the full network configuration the way Windows does.

How to View Your IP Address on a Mac

To see your IP address and other network details, open the Terminal app (in /Applications/Utilities/) and use one of these commands:

  • ifconfig – shows all network interfaces, including en0 (usually Wi-Fi) and en1 (usually Ethernet). Look for inet followed by an IP like 192.168.1.10.
  • ipconfig getifaddr en0 – prints just the IPv4 address of the Wi-Fi interface.
  • ipconfig getifaddr en1 – prints just the IPv4 address of the Ethernet interface.
  • route -n get default – shows your default gateway (router) IP.

If you prefer a graphical way, go to System Settings > Network, select your active connection, and click Details. You’ll see the IP address, subnet mask, and router.

How to Renew a DHCP Lease on a Mac

When your Mac has a wrong or stale IP address, you can force it to get a new one from the router. In Terminal, type:

sudo ipconfig set en0 DHCP

This releases the current lease and requests a new one. You’ll need to enter your admin password. If you want to do it without sudo, you can use ipconfig set en0 DHCP but it may fail due to permissions. To release the lease without renewing, use sudo ipconfig set en0 NONE.

Alternatively, you can do it graphically: System Settings > Network > select the connection > Details > TCP/IP > Renew DHCP Lease.

Common Problems and Fixes

  • “ipconfig: command not found” – This happens if you are in a shell that doesn’t include /sbin in PATH. Use the full path: /sbin/ipconfig or just use ifconfig.
  • “Permission denied” – Some ipconfig subcommands require root. Prefix with sudo.
  • No IP address showing – If ifconfig shows no inet line, your Wi-Fi or Ethernet is not connected. Check that Wi-Fi is on and you’re in range.
  • Wrong interface name – On newer Macs, Wi-Fi is en0, but on some older models it could be en1. Run ifconfig and look for the one with an IP address.

ifconfig vs. ipconfig vs. ip

On Linux, the modern command is ip (from iproute2), and ifconfig is deprecated but still present. On macOS, ifconfig is the standard tool for viewing and configuring interfaces. The ip command is not installed by default on macOS (you can install it via Homebrew, but it’s not necessary). So the equivalents are:

  • Windows ipconfig → macOS ifconfig (view) and ipconfig (DHCP lease)
  • Windows ipconfig /release → macOS sudo ipconfig set en0 NONE
  • Windows ipconfig /renew → macOS sudo ipconfig set en0 DHCP
  • Windows ipconfig /flushdns → macOS sudo dscacheutil -flushcache (or sudo killall -HUP mDNSResponder)

What About the DNS Cache?

Windows users often flush DNS with ipconfig /flushdns. On macOS, the equivalent is:

sudo dscacheutil -flushcache; sudo killall -HUP mDNSResponder

This clears the local DNS cache. You may need to do this after changing DNS settings or when websites don’t load correctly.

Frequently Asked Questions

Does macOS have ipconfig?

Yes, macOS includes an ipconfig command, but it’s not a full replacement for Windows’ ipconfig. It only handles DHCP lease operations and a few other tasks. For viewing IP addresses, use ifconfig.

How do I find my IP address on a Mac?

Open Terminal and type ifconfig. Look for the interface that is active (en0 for Wi-Fi, en1 for Ethernet) and find the line starting with inet. That’s your IPv4 address. Alternatively, use ipconfig getifaddr en0.

Why does ipconfig show nothing on my Mac?

Because the macOS ipconfig command doesn’t display a summary like Windows does. If you type ipconfig alone, it shows usage information. To see your IP, use ifconfig or ipconfig getifaddr en0.

What is the difference between ifconfig and ipconfig on Mac?

ifconfig is the older Unix tool for viewing and configuring network interfaces. ipconfig on macOS is a specific tool for DHCP client configuration. They serve different purposes; you’ll use ifconfig more often for diagnostics.

How do I renew my IP address on a Mac?

In Terminal, run sudo ipconfig set en0 DHCP. This releases the old lease and requests a new one. You can also do it in System Settings > Network > Details > TCP/IP > Renew DHCP Lease.

Can I use the same ipconfig commands as Windows on a Mac?

No. Windows commands like /release, /renew, and /flushdns do not work on macOS. You need to use the macOS equivalents, which are different.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →