keepcalculator

06 Numbers and Powers

Snowblower Maintenance Check Winter? Essential Guide

Card No. 06·83924 · Updated · Standard formula, shown below

Yes, a snowblower needs a maintenance check before winter to ensure it starts reliably and runs safely in cold, snowy conditions. This article outlines the essential steps—from fuel and oil to auger shear pins and belt inspection—so you can prepare your machine for the season.

Why Winter Maintenance Matters

A snowblower sits idle for months, and that idle period is when problems develop. Old fuel can gum up the carburetor, oil can lose its protective properties, and rubber belts can crack from heat and ozone. A pre-season check prevents the most common frustration: a machine that won’t start when you need it most—during a heavy snowfall. Regular maintenance also extends the life of the machine and reduces the risk of mechanical failure mid-job, which is both inconvenient and potentially dangerous if you’re clearing a steep driveway.

The Pre-Season Checklist

Before the first snowfall, work through this checklist. It takes about an hour and covers the critical systems.

  • Fuel system: If you left fuel in the tank from last season, drain it completely or add a fuel stabilizer and run the engine for a few minutes to circulate it. Old fuel (more than 30 days old) can varnish and clog the carburetor. For the new season, use fresh gasoline with an ethanol content of 10% or less if possible.
  • Oil: Check the oil level with the dipstick. If the oil looks dark or smells burnt, change it. Most small engines require SAE 5W-30 or 10W-30, but check your owner’s manual. Change the oil at least once per season or every 50 hours of operation.
  • Spark plug: Remove the spark plug and inspect the electrode. If it’s worn, fouled, or the gap is out of specification, replace it. A new spark plug ensures easy starting and efficient combustion.
  • Belts: Inspect the drive belt and auger belt for cracks, fraying, or glazing. Replace any belt that shows wear. Check belt tension—most machines have a spring-loaded tensioner, but some require manual adjustment.
  • Auger and impeller: Check the auger blades for wear or damage. Replace them if they are rounded or chipped. Also check the shear pins—these are designed to break if the auger hits an obstacle. Replace any that are bent or missing, and keep spares on hand.
  • Skid shoes and scraper bar: These wear down from scraping against pavement. If the skid shoes are worn more than half their original height, replace them. The scraper bar should be replaced if it’s worn to less than ¼ inch thick.
  • Chute and controls: Lubricate the chute rotation mechanism and the control cables. Check that the chute directional control moves smoothly and that the auger engagement lever engages and disengages properly.
  • Tires: Check tire pressure—typically 15-20 psi for snowblowers. Inflate to the recommended pressure listed on the tire sidewall or in the manual.

Fuel and Oil: The Two Most Common Failure Points

Most snowblower starting problems trace back to fuel or oil. Old fuel loses its volatility, making cold starts difficult. Ethanol-blended fuel attracts moisture and can cause corrosion. The solution is to use a fuel stabilizer every time you fill the tank, and to run the engine for a few minutes after adding stabilizer so it reaches the carburetor. At the end of the season, either drain the fuel tank completely or run the engine until it stops from lack of fuel.

Oil is the lifeblood of the engine. Over the summer, oil can break down and become acidic. Always check the oil level before each use, and change it at the start of the season. Use the oil viscosity recommended in your owner’s manual—most small engines use 5W-30 or 10W-30. Do not overfill; too much oil can cause the engine to smoke and leak.

Common Problems and How to Fix Them

Even with regular maintenance, issues can arise. Here are the most common problems and their typical causes:

  • Engine won’t start: Check the spark plug, fuel, and choke. Make sure the fuel shut-off valve (if equipped) is open. If the engine cranks but won’t start, it’s likely a fuel delivery issue—clean the carburetor or replace the fuel filter.
  • Engine runs but won’t move: This usually points to the drive belt. A worn or loose belt will slip. Inspect and adjust or replace the belt.
  • Auger doesn’t turn: Check the shear pins. They are designed to break to protect the gearbox. Replace with the correct size—do not use a stronger bolt, as that can damage the gearbox.
  • Auger turns but doesn’t throw snow: The impeller (the fan-like component) may be clogged with ice or debris. Clear it with a stick—never your hand. Also check the chute for blockages.
  • Snow throwing distance is weak: The engine RPM may be too low, or the belts are slipping. Also check the auger speed—if the auger is spinning too slowly, it won’t throw snow far.

Safety First: Pre-Use Checks

Before each use, take a minute to ensure the machine is safe:

  • Check that all safety guards and shields are in place.
  • Verify that the auger and drive controls disengage when released.
  • Never put your hand into the chute or auger housing—use a stick or broom handle to clear clogs.
  • Always shut off the engine before clearing a jam or performing any maintenance.
  • Use the machine only in daylight or with adequate artificial light.

End-of-Season Storage

Proper storage prevents next year’s problems. After the last snowfall:

  1. Run the engine until it runs out of fuel, or add a fuel stabilizer and run for a few minutes.
  2. Change the oil.
  3. Remove the spark plug and add a teaspoon of oil into the cylinder. Pull the starter rope a few times to coat the cylinder walls, then replace the plug.
  4. Clean the machine thoroughly, removing salt and dirt.
  5. Lubricate all moving parts.
  6. Store in a dry place, preferably with the fuel tank empty.

Frequently Asked Questions

How often should I change the oil in my snowblower?

Change the oil at least once per season, or every 50 hours of operation, whichever comes first. If you use the machine heavily, change it more often. Always use the oil grade specified in your owner’s manual.

Can I use regular car oil in my snowblower?

Yes, if the viscosity matches what your manual recommends. Most small engines use 5W-30 or 10W-30, which are common car oils. However, some manuals recommend synthetic oil for better cold-weather performance. Check the manual.

What is a shear pin and why does it break?

A shear pin is a deliberately weak bolt that connects the auger to the drive shaft. It breaks if the auger hits a hard object (like a rock or ice chunk), preventing damage to the gearbox. Always replace with the correct shear pin—never use a standard bolt, as that could cause costly damage.

Should I use ethanol-free gas?

Ethanol-free gas is recommended if you can find it, as it doesn’t attract moisture and has a longer shelf life. If you use regular gas with ethanol, add a fuel stabilizer and drain the tank at the end of the season.

Why does my snowblower backfire when I shut it off?

Backfiring on shutdown is often caused by a lean fuel mixture or carbon buildup. It can also happen if the engine is running too hot. Check the carburetor adjustment and clean any carbon deposits from the cylinder head. If the problem persists, consult a small engine mechanic.

Do I need to replace the spark plug every year?

It’s a good practice to replace the spark plug annually. A new plug ensures easy starting and optimal combustion. If you don’t replace it, at least inspect it and clean the electrode with a wire brush. Check the gap against the manual’s specification.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →