Tangential flow filtration (TFF) explained: membrane retention is the ability to hold back particles above a certain size, flux is the flow rate through the membrane per unit area, and shear is the tangential force that sweeps the membrane surface to prevent fouling. This article explains how these three parameters interact and how to choose operating conditions for a TFF process.
What Is Tangential Flow Filtration?
Tangential flow filtration (also called crossflow filtration) is a separation technique where the feed stream flows parallel to the membrane surface, unlike dead-end filtration where the feed flows directly into the membrane. The parallel flow creates a shear force that continuously sweeps away retained particles, allowing the process to run for extended periods without rapid clogging. TFF is widely used in biopharmaceutical manufacturing for concentrating proteins, cell harvesting, diafiltration (buffer exchange), and virus removal.
The key difference from dead-end filtration is that TFF has two outlet streams: the permeate (what passes through the membrane) and the retentate (what is retained and recirculated). This design allows the retained material to be continuously concentrated while the permeate is removed.
Membrane Retention: What Gets Caught
Membrane retention is the ability of the membrane to reject particles or solutes of a given size. It is typically expressed as a molecular weight cut-off (MWCO) for ultrafiltration membranes, measured in kilodaltons (kDa). A 10 kDa membrane will retain most molecules larger than 10 kDa, but the cut-off is not a sharp threshold—it is a nominal value, and actual retention depends on molecular shape, charge, and operating conditions.
For microfiltration membranes (pore size 0.1–10 µm), retention is based on particle size. For example, a 0.2 µm membrane is used for sterile filtration because it retains bacteria. Retention is not absolute; some particles of the target size may pass through, especially if the membrane is damaged or if concentration polarization reduces effective pore size.
In practice, retention is measured by the sieving coefficient (S), which is the ratio of solute concentration in the permeate to that in the retentate. A sieving coefficient of 0 means complete retention, while 1 means free passage. For a desired product, you want a high retention (S near 0) if it is in the retentate, or a low retention (S near 1) if it is in the permeate.
Flux: How Fast the Permeate Flows
Flux is the volumetric flow rate of permeate per unit membrane area, typically expressed in liters per square meter per hour (LMH) or gallons per square foot per day (GFD). It is the primary measure of productivity in TFF. The flux is driven by the transmembrane pressure (TMP), which is the average pressure difference between the feed/retentate side and the permeate side.
Flux is not constant over time. Initially, flux is high, but as a fouling layer builds up on the membrane, flux declines. The steady-state flux is often much lower than the clean-water flux. The relationship between flux and TMP is linear in the pressure-controlled regime, but at higher pressures, flux becomes mass-transfer limited—increasing TMP no longer increases flux because the fouling layer reaches a limiting thickness.
Typical flux values for ultrafiltration of protein solutions range from 10 to 100 LMH, depending on the feed composition and operating conditions. For microfiltration of cell suspensions, fluxes are lower, often 5–50 LMH, due to the high solids content.
Shear: The Cleaning Force
Shear rate is the velocity gradient at the membrane surface, caused by the tangential flow of the feed. It is proportional to the crossflow velocity and inversely proportional to the channel height. Higher shear rates increase the back-transport of particles away from the membrane, reducing fouling and maintaining higher flux.
However, shear can damage shear-sensitive products, such as mammalian cells or large proteins. For cell harvesting, shear rates must be kept below a threshold that causes cell lysis. For protein concentration, high shear is generally safe, but very high shear can denature some proteins. Therefore, the optimal shear rate is a trade-off between fouling control and product integrity.
Shear rate is not uniform across the membrane channel; it is highest at the wall and zero at the center. The wall shear rate (γ) can be estimated from the crossflow velocity (v) and the channel hydraulic diameter (Dh) using the relation γ ≈ 8v/Dh for laminar flow. In practice, manufacturers provide shear rate ranges for their cassettes or hollow fiber modules.
How to Choose Operating Parameters
Selecting the right TFF conditions requires balancing flux, retention, and shear. Here are the key steps:
- Determine the product and its size: choose a membrane with a MWCO or pore size that retains the product but allows impurities to pass.
- Set the crossflow rate: higher crossflow increases shear, reducing fouling, but may damage the product. Start with the manufacturer’s recommended range for the module.
- Set the TMP: begin at a low TMP and increase gradually until flux plateaus. Operating at the plateau (mass-transfer limit) is usually optimal.
- Monitor flux and retention: if flux declines too fast, increase crossflow or reduce TMP. If retention drops, check for membrane integrity or concentration polarization.
- For diafiltration, use a constant volume or variable volume strategy, and ensure the buffer composition is compatible with the membrane.
It is also important to consider the feed concentration. As the retentate becomes more concentrated, viscosity increases, which reduces crossflow and increases TMP. This can lead to a self-limiting process where flux drops sharply. In such cases, a larger membrane area or a different module design may be needed.
Common Problems and Troubleshooting
Several issues can arise during TFF operation:
- Low flux: often due to fouling, low TMP, or high feed viscosity. Increase crossflow, clean the membrane, or reduce concentration.
- Poor retention: may be caused by membrane damage, improper membrane selection, or concentration polarization that alters the effective cut-off. Verify membrane integrity and consider a tighter membrane.
- High pressure drop: indicates channel blockage or excessive viscosity. Reduce feed concentration or increase channel height.
- Product loss: check for leaks in the system, or if the product is passing through the membrane due to low retention.
- Foaming: can denature proteins; avoid by keeping the retentate line submerged and reducing crossflow if necessary.
Regular cleaning and sanitization are essential to restore flux and maintain membrane life. Cleaning agents include sodium hydroxide, detergents, and enzymes, but must be compatible with the membrane material.
TFF vs. Dead-End Filtration
Dead-end filtration is simpler and cheaper for low-solids feeds, but it suffers from rapid fouling and requires frequent filter changes. TFF is preferred when the feed has high solids or when the product is shear-sensitive and needs gentle handling. TFF also allows continuous operation and easy scale-up, making it the standard in bioprocessing.
For example, sterilizing a buffer with a 0.2 µm dead-end filter is common, but concentrating a cell culture harvest requires TFF because the cell density would quickly clog a dead-end filter. Similarly, diafiltration to remove salts from a protein solution is only practical with TFF, as it allows continuous buffer exchange.
Cost and Scale-Up Considerations
The cost of TFF includes the membrane modules, pumps, and system hardware. Membrane modules are consumable and need periodic replacement. Scale-up is typically done by increasing membrane area (adding more cassettes or hollow fiber modules) rather than changing the flow path. It is important to maintain the same crossflow rate per channel and TMP to achieve similar performance at larger scale.
For process development, small-scale cassettes with a few square centimeters of membrane area are used to screen conditions. Results can be scaled linearly if the channel geometry and fluid dynamics are kept similar. However, differences in pump type and system hold-up volume can affect performance, so pilot-scale verification is recommended.
Frequently Asked Questions
What is the difference between flux and flow rate?
Flow rate is the volume of permeate per unit time (e.g., L/h), while flux is the flow rate normalized to the membrane area (e.g., LMH). Flux allows comparison between systems of different sizes.
How do I increase flux in TFF?
Increase crossflow velocity (to raise shear), increase TMP (up to the mass-transfer limit), reduce feed viscosity by dilution or temperature, and ensure the membrane is clean. Also, choose a membrane with a larger pore size if retention allows.
What is the typical shear rate in TFF?
Shear rates vary widely: for hollow fiber modules, wall shear rates are often 2000–8000 s-1; for flat sheet cassettes, they can be 3000–10000 s-1. The exact value depends on channel geometry and crossflow velocity.
Can TFF be used for virus removal?
Yes, TFF with ultrafiltration membranes (e.g., 20–50 nm pore size) can remove viruses by size exclusion. However, virus retention is not absolute, and dedicated virus filters are often used in series for safety.
Why does flux decline over time?
Flux decline is caused by membrane fouling (particle deposition, gel layer formation, or pore blocking) and concentration polarization. Regular cleaning and optimizing operating conditions can minimize it.
What is diafiltration in TFF?
Diafiltration is a TFF mode where buffer is added to the retentate while permeate is removed, washing out small molecules. It is used for buffer exchange or to remove impurities.
Related
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.
More cards in this drawer
- Funny Subreddits That Make You Laugh
- Why Retro Gaming Is Still Worth Playing Today
- Skip Ryobi and Milwaukee? Harbor Freight Tools to Buy
- Neptune Facts That Will Blow Your Mind
- Survival Crafting Game Fatigue: Why & How to Fix It
- Sell Your EV Now Before Prices Plummet?