keepcalculator

06 Numbers and Powers

Used Storage Buying Guide: What’s Actually Safe

Card No. 06·85821 · Updated · Standard formula, shown below

Cost per GB 0.050 USD/GB
Drive capacity (GB)
1000 GB
You entered
Price (USD)
50 USD
You entered
You enter
Drive capacity (GB), Price (USD)
You get
Cost per GB
Rounding
3 dp

When buying used storage, the only kind you should be buying is a drive that has been properly tested, verified, and comes with a clear health report—specifically, enterprise-grade drives with known usage history or consumer drives from reputable sellers that show low power-on hours and no reallocated sectors. This answer applies to both hard disk drives (HDDs) and solid-state drives (SSDs), but the specific checks differ. Below, we break down what makes a used drive worth buying, how to evaluate it, and when to walk away.

Formula

The cost per gigabyte is simply the price divided by the capacity:

Cost per GB = Price (USD) / Capacity (GB)

  • Price – what you pay for the used drive, in US dollars.
  • Capacity – the formatted capacity of the drive, in gigabytes (GB). For a 1 TB drive, enter 1000 GB.

The result is the cost per gigabyte, which lets you compare used drives against new ones and against each other. A lower number means better value, but only if the drive is healthy.

Worked Example

Using the defaults: a 1000 GB (1 TB) drive costs $50.

  1. Divide price by capacity: 50 / 1000 = 0.05
  2. Cost per GB = $0.05

That is 5 cents per gigabyte. For comparison, a new 1 TB drive might cost $40–$60, so a used drive at $50 is not a bargain unless it has very low usage. The calculator shows the same result: 0.050 USD/GB.

Why Buy Used Storage at All?

Used drives cost significantly less than new ones. A 4 TB enterprise HDD that retailed for $200+ can often be found used for $50–$80. For homelabs, media servers, or backup arrays, that price difference matters. But the savings come with risk: a used drive has already been running, possibly for years, and its remaining lifespan is unknown. The key is to buy drives that have been tested and certified by the seller, not just pulled from a decommissioned server and shipped as-is.

Two main categories of used drives exist:

  • Pulled from enterprise servers – These are usually high-end HDDs (e.g., 10K or 15K RPM SAS drives) or enterprise SSDs. They have high endurance and are often sold in bulk. Many sellers provide SMART data and a 30-day warranty.
  • Pulled from consumer devices – Laptop or desktop drives, often from upgrades. These may have been used lightly (e.g., a 2.5″ drive from an old laptop) or heavily (e.g., a NAS drive that ran 24/7 for 5 years).

How to Evaluate a Used Drive

Before buying, you need the drive’s SMART (Self-Monitoring, Analysis, and Reporting Technology) data. This is a built-in diagnostic that tracks hundreds of attributes. The most important ones are:

  • Reallocated Sectors Count – The number of bad sectors that have been remapped. Zero is ideal; anything above a handful (e.g., 10+) is a red flag for HDDs. For SSDs, this is less critical but still relevant.
  • Power-On Hours (POH) – Total hours the drive has been powered on. For HDDs, 3–5 years of 24/7 use is roughly 26,000–44,000 hours. Drives with less than 20,000 hours are considered lightly used. For SSDs, POH matters less than total bytes written (TBW).
  • Power Cycle Count – How many times the drive was turned on/off. High counts are normal for consumer drives.
  • Current Pending Sector Count – Sectors that are unstable and might fail soon. Should be zero.
  • Uncorrectable Errors – Errors that could not be fixed. Should be zero.

For SSDs, also look at Total Bytes Written (TBW) and compare it to the drive’s endurance rating (often in the spec sheet). For example, a 1 TB SSD with a 600 TBW rating that has written 50 TB is barely used.

What to Avoid

Some used drives are not worth any price:

  • Drives with reallocated sectors – Even one is a sign of physical damage. The drive is compensating for failed areas, and more will likely fail.
  • Drives with high POH and no warranty – A 50,000-hour HDD with no return policy is a gamble.
  • Mystery pulls – Sellers who cannot provide SMART data or a clear model number. If they won’t share the health report, assume it’s bad.
  • Drives that have been dropped or physically damaged – You can’t see this from SMART, but a seller who says “cosmetic damage only” is a risk.
  • SSDs with very high TBW – If the drive has written more than 80% of its endurance, it may start failing soon.

How to Test a Used Drive After Purchase

Even if the seller provides SMART data, you should verify it yourself. When the drive arrives:

  1. Connect it as a secondary drive (not your boot drive).
  2. Run a full surface scan or read test using tools like badblocks (Linux) or HD Tune (Windows). This reads every sector and will catch weak spots.
  3. Check SMART data again after the scan. Reallocated sectors may increase if the drive is failing.
  4. For SSDs, run a TRIM check and a full write/read cycle if possible.
  5. If the drive passes, use it for non-critical data first (e.g., media files) for a few weeks before trusting it with backups.

If the drive fails any test, return it if you have a warranty. If not, you’ve learned a lesson.

HDD vs. SSD: Which Used Type Is Safer?

Used HDDs are more common and cheaper, but they have moving parts that wear out. A used enterprise HDD with low hours can be a good deal, but it will still be slower and more fragile than a new SSD. Used SSDs have no moving parts, so they are less prone to shock damage, but they have a finite write endurance. However, most consumer SSDs have endurance ratings far above what a typical user writes, so a used SSD with moderate TBW is often a better buy than a used HDD with high hours.

For example, a 1 TB Samsung 860 EVO has a TBW rating of 600 TB. If a used one shows 50 TB written, that’s 8% of its life used. A 1 TB HDD with 30,000 hours is roughly 3.4 years of 24/7 use, which is about 50% of its expected lifespan (assuming 5-year warranty). The SSD is the safer bet.

Where to Buy Used Storage

Reputable sources include:

  • Specialized used hardware retailers – They often test drives, provide SMART data, and offer 30–90 day warranties.
  • Online marketplaces with seller ratings – Look for sellers with many positive reviews and clear return policies.
  • Business liquidators – They sell decommissioned enterprise equipment in bulk. You can sometimes buy a single drive, but you’ll need to ask for SMART data.

Avoid auction sites with no return policy, “for parts” listings, or sellers who refuse to share health data.

Cost Comparison: Used vs. New

Use the calculator above to compare. As a rough guide:

  • New consumer HDDs: $0.02–$0.04 per GB (e.g., $50 for 2 TB).
  • Used enterprise HDDs: $0.01–$0.03 per GB.
  • New SSDs: $0.05–$0.10 per GB.
  • Used SSDs: $0.03–$0.07 per GB.

If a used drive costs more than 70% of a new equivalent, it’s usually not worth it, unless you need a specific form factor (e.g., 2.5″ 15mm thick enterprise drive) that is hard to find new.

Common Mistakes and Misconceptions

  • Mistaking “refurbished” for “tested” – Refurbished can mean anything from a simple wipe to a full replacement of internals. Always ask for the specific test report.
  • Ignoring the warranty – A used drive without a warranty is a paperweight if it fails. Even a 30-day warranty is better than none.
  • Using a used drive for your only backup – Never. Use a used drive for non-critical data or as part of a RAID array with redundancy.
  • Assuming all SMART data is accurate – Some sellers reset SMART counters. This is rare but possible. A physical inspection and your own test are the only way to be sure.

Frequently Asked Questions

Is it safe to buy a used hard drive from eBay?

It can be, but only from sellers with high ratings and a clear return policy. Always ask for the SMART data before bidding. If the seller doesn’t provide it, move on. After receiving the drive, run a full surface scan immediately.

How many power-on hours is too many for a used HDD?

For a 3.5″ consumer HDD, anything above 30,000 hours is high risk. Enterprise drives are rated for 24/7 operation, so 40,000 hours might be acceptable if the SMART data is clean. But the lower the better—aim for under 20,000 hours if possible.

Can I trust a used SSD for my operating system?

Yes, if the SSD has low TBW and passes a full write/read test. SSDs fail differently than HDDs—they often just stop working without warning. So keep a backup. For an OS drive, a used SSD with less than 10% of its endurance used is generally fine.

What is the difference between SAS and SATA used drives?

SAS drives are enterprise-grade, often faster (10K/15K RPM) and have better error handling. They require a SAS controller, which most consumer motherboards don’t have. SATA drives are standard for home use. Unless you have a SAS controller, stick to SATA.

Should I buy a used drive for a NAS?

Only if the drive is designed for NAS (e.g., WD Red, Seagate IronWolf) and has low hours. NAS drives run 24/7, so a used one with 30,000 hours is near the end of its life. It’s safer to buy new for a NAS, or use used drives only in a RAID with a spare.

How can I check the TBW on a used SSD?

Use a tool like CrystalDiskInfo (Windows) or smartctl (Linux). Look for the “Total Host Writes” or “Media Wear Out Indicator” attribute. Compare it to the drive’s rated TBW from the manufacturer’s spec sheet.

Related

Formula used
in t | Drive capacity (GB) | GB | 1000 | 1 | 100000
in p | Price (USD) | USD | 50 | 0 | 10000
out c | Cost per GB | USD/GB | p / t | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →