keepcalculator

06 Numbers and Powers

Silicon Photonics: What It Is & Data Centre Uses

Card No. 06·73352 · Updated · Standard formula, shown below

Effective bandwidth 80.00 Gbps
Bandwidth in Gbps
80.00 Gbps
Result
Data transfer time
10 seconds
You entered
Data volume
100 GB
You entered
You enter
Data transfer time, Data volume
You get
Effective bandwidth, Bandwidth in Gbps
Rounding
2 dp

Silicon photonics is a technology that uses standard semiconductor manufacturing processes to build optical components—such as lasers, modulators, and detectors—on a silicon chip. Instead of sending data as electrical signals through copper wires, it sends data as light pulses through tiny optical waveguides etched into the silicon. In a data centre network, this means much higher bandwidth, lower latency, and significantly less power consumption than traditional copper interconnects, especially as link speeds move beyond 400G per lane.

Formula

The calculator above works out the effective bandwidth of a data link given the amount of data transferred and the time taken. The formula is:

Bandwidth (Gbps) = (Data volume in GB × 8) / Time in seconds

Where:

  • Data volume – the amount of data transferred, in gigabytes (GB). 1 GB = 10⁹ bytes.
  • Time – the duration of the transfer, in seconds.
  • Bandwidth – the effective data rate, in gigabits per second (Gbps).

The factor 8 converts bytes to bits, because data rates are always quoted in bits per second.

Worked Example

Using the default values from the calculator: transfer 100 GB in 10 seconds.

  1. Convert GB to bits: 100 GB × 8 = 800 gigabits.
  2. Divide by time: 800 Gb / 10 s = 80 Gbps.

The calculator returns an effective bandwidth of 80.00 Gbps.

Why Silicon Photonics Matters for Data Centres

Data centre traffic has grown exponentially over the past decade, driven by cloud computing, video streaming, and AI training. Traditional copper cabling struggles at speeds above 100G per lane because of signal loss and crosstalk. Silicon photonics offers a way to keep up with demand by integrating optical functions onto a silicon chip, which is cheap to mass-produce using existing CMOS fabrication lines.

The key benefit is that light travels faster and with less loss than electricity in copper. For example, a 400G-DR4 module using silicon photonics can transmit data over 500 metres of single-mode fibre, while copper would need active retiming every few metres. This reduces the number of repeaters and the power needed to drive them.

How Silicon Photonics Works

A silicon photonics chip typically contains several components fabricated on a single substrate:

  • Laser – usually an external III-V laser (e.g., indium phosphide) coupled to the silicon chip, because silicon does not emit light efficiently.
  • Modulator – changes the intensity or phase of light to encode data. Silicon modulators use the free-carrier plasma dispersion effect, where injecting carriers changes the refractive index.
  • Waveguide – a microscopic silicon core (typically 450 nm × 220 nm) that confines light and routes it around the chip.
  • Photodetector – usually made of germanium grown on silicon, which absorbs light and converts it back to an electrical signal.
  • Multiplexer/de-multiplexer – combines or separates different wavelengths to increase bandwidth per fibre.

The entire assembly is packaged with a fibre array and control electronics, forming a pluggable optical transceiver such as a QSFP-DD or OSFP module.

How to Choose: Silicon Photonics vs. Alternatives

When deciding between silicon photonics and other interconnect technologies, consider the following factors:

  • Reach – Silicon photonics supports distances from a few metres to several kilometres with single-mode fibre. For very short chip-to-chip links, copper or co-packaged optics might be more cost-effective.
  • Data rate – For 800G and beyond, silicon photonics is often the only practical solution because of the bandwidth density it offers.
  • Power budget – Silicon photonics modules typically consume 10–20% less power than equivalent VCSEL-based modules at the same speed.
  • Cost – At high volumes, silicon photonics is cheaper than discrete optical components because it leverages CMOS manufacturing. However, the initial design cost is high.
  • Latency – Light travels at about 200,000 km/s in silicon, which is slower than in vacuum but still faster than electrical signals in copper. The difference is negligible for most data centre applications.

Common Problems and Misconceptions

One common misconception is that silicon photonics uses pure silicon for everything. In reality, silicon cannot emit light efficiently because of its indirect bandgap, so lasers are always made of III-V materials. The term “silicon photonics” refers to the platform, not the entire component.

Another issue is coupling loss. Light from a single-mode fibre must be coupled into a silicon waveguide that is much smaller than the fibre’s core. This requires precise alignment and often uses grating couplers or edge couplers, which can introduce a few dB of loss. Packaging is therefore a significant cost and technical challenge.

Thermal sensitivity is also a concern. Silicon’s refractive index changes with temperature, so modulators and filters need active temperature control to maintain performance. This adds complexity and power consumption.

Cost and Implementation Considerations

The cost of silicon photonics has fallen dramatically as the technology matured. Early modules were expensive because of low volumes and custom packaging. Today, a 400G silicon photonics transceiver costs roughly the same as a VCSEL-based one, and the price per bit continues to drop.

However, deploying silicon photonics in a data centre requires a shift to single-mode fibre infrastructure. Most existing data centres use multimode fibre with VCSELs, which cannot support the distances or speeds that silicon photonics provides. Upgrading the cabling plant is a significant capital expense.

Safety and Reliability

Silicon photonics modules use Class 1 laser products, which are safe under normal operating conditions because the light is enclosed. However, technicians must never look directly into a fibre connector or a laser aperture, as invisible infrared light can damage the retina. Follow standard laser safety procedures such as using an optical power meter to verify that the laser is off before handling connectors.

In terms of reliability, silicon photonics modules are designed for data centre environments with a typical mean time between failures (MTBF) of several million hours. The main failure modes are laser degradation and fibre misalignment, both of which are mitigated by robust packaging and burn-in testing.

Frequently Asked Questions

What is the difference between silicon photonics and traditional optics?
Traditional optics uses discrete components like separate laser diodes, modulators, and photodetectors, which are assembled into a module. Silicon photonics integrates all of these onto a single silicon chip using CMOS fabrication, which reduces size, cost, and power consumption.

Can silicon photonics be used for long-haul networks?
Yes, but it is most common in data centre interconnects (DCI) of up to a few kilometres. For longer distances, coherent transmission using silicon photonics is possible, but it competes with established technologies like indium phosphide.

Why doesn’t silicon emit light?
Silicon has an indirect bandgap, meaning that when electrons recombine with holes, the energy is released as heat (phonons) rather than photons. This makes light emission extremely inefficient. That’s why lasers use III-V materials like gallium arsenide or indium phosphide.

What is co-packaged optics?
Co-packaged optics places the optical engine on the same package as the switch ASIC, eliminating pluggable modules and reducing electrical trace length. This improves bandwidth density and power efficiency, and silicon photonics is a leading candidate for this approach.

Is silicon photonics faster than copper?
At the same distance, yes. Light in silicon travels at about 200,000 km/s, while electrical signals in copper travel at about 60–80% of the speed of light, but they also suffer from attenuation and crosstalk. For links longer than a few metres, silicon photonics offers lower latency and higher bandwidth.

Related

Formula used
in t | Data transfer time | seconds | 10 | 0.001 | 86400
in d | Data volume | GB | 100 | 0.001 | 1000000
out bw | Effective bandwidth | Gbps | (d * 8) / t | 2
out bw_gbps | Bandwidth in Gbps | Gbps | (d * 8) / t | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →