keepcalculator

06 Numbers and Powers

3D Printer Materials: How to Choose the Right Filament

Card No. 06·71353 · Updated · Standard formula, shown below

3D printers can use a wide range of materials, from everyday thermoplastics like PLA and ABS to specialized resins, nylons, and metal-filled composites. Choosing the right one depends on your part’s required strength, flexibility, heat resistance, surface finish, and your printer’s capabilities. This guide breaks down the most common materials, how they compare, and the practical factors that should drive your choice.

How 3D Printing Materials Work

Most desktop 3D printers use Fused Deposition Modeling (FDM), which melts a thermoplastic filament and extrudes it layer by layer. The material is solid at room temperature, becomes fluid when heated through a nozzle, and re-solidifies as it cools. The two key properties that define a filament are its glass transition temperature (the point where it softens) and its melting temperature (where it flows). Printers must heat the nozzle above the melting point and the bed to a temperature that keeps the first layers adhered.

Another major technology is Stereolithography (SLA), which uses liquid photopolymer resin that hardens when exposed to UV light. Resins offer much finer detail than FDM but are brittle and require post-processing (washing and curing). There is also Selective Laser Sintering (SLS), which fuses nylon powder with a laser, producing strong, durable parts without supports, but the machines are expensive and mostly industrial.

Common FDM Filaments: PLA, ABS, PETG, and More

  • PLA (Polylactic Acid): The easiest filament to print. Made from cornstarch or sugarcane, it prints at low temperatures (190–220°C nozzle, 50–60°C bed) and warps very little. It is stiff but brittle, and it degrades in sunlight and heat (softens around 60°C). Ideal for prototypes, decorative items, and parts that won’t bear heavy loads.
  • ABS (Acrylonitrile Butadiene Styrene): Stronger and more heat-resistant than PLA (softens around 100°C), but it shrinks as it cools, causing warping and layer separation. Requires a heated bed (100–110°C) and an enclosed printer to maintain a stable temperature. It emits fumes, so good ventilation is necessary. Used for functional parts like brackets and enclosures.
  • PETG (Polyethylene Terephthalate Glycol): A great middle ground. It is nearly as easy to print as PLA, but stronger, more flexible, and more heat-resistant (softens around 80°C). It adheres well to a bed at 70–80°C and resists moisture and chemicals. Common for food containers (though not all PETG is food-safe), mechanical parts, and outdoor items.
  • TPU (Thermoplastic Polyurethane): A flexible rubber-like filament. It can stretch and absorb impact, but it is tricky to print because it bends and jams in the extruder. Requires a direct-drive extruder and slow speeds. Used for phone cases, gaskets, and vibration dampeners.
  • Nylon (Polyamide): Very strong, durable, and abrasion-resistant, with good heat resistance (softens around 150°C). It absorbs moisture from the air, so it must be dried before printing. Prints at 240–270°C and requires a heated bed (70–90°C) and often an enclosure. Used for gears, hinges, and functional engineering parts.
  • Polycarbonate (PC): Extremely strong and heat-resistant (softens around 150°C), but it warps severely and needs a very high nozzle temperature (270–310°C) and an enclosed printer. Used for structural parts that must withstand high temperatures or impacts.

Specialty and Composite Filaments

Beyond the basics, you can mix plastics with other materials to change properties:

  • Wood-filled PLA: Contains wood fibers, giving a matte, wood-like finish. Prints like PLA but needs a larger nozzle (0.5mm or more) to avoid clogging. The part can be sanded and stained.
  • Metal-filled PLA: Contains metal powders (bronze, copper, stainless steel). Heavier and stiffer than PLA, and can be polished to a metallic shine. Requires a hardened steel nozzle because the abrasive particles wear out brass nozzles.
  • Carbon-fiber reinforced: Usually nylon or PETG with short carbon fibers. Greatly increases stiffness and reduces weight, but is abrasive and requires a hardened nozzle. Used for drone frames, automotive parts, and robotics.
  • Glow-in-the-dark: PLA mixed with strontium aluminate. Prints like PLA but is abrasive, so a hardened nozzle is recommended.
  • Conductive filament: PLA or TPU with carbon black, allowing it to carry low-voltage current. Used for simple touch sensors or LED circuits, but its resistance is high and inconsistent.

Resins for SLA Printing

Resin printing produces smooth, highly detailed parts, but the materials are different from filaments:

  • Standard resin: Prints fast and gives a glossy finish, but is brittle and degrades in sunlight. Good for miniatures, jewelry molds, and display models.
  • Tough resin: Formulated to resist impact and bending, closer to ABS in strength. Used for functional prototypes and snap-fit parts.
  • Flexible resin: Can bend and compress, similar to TPU. Used for gaskets, seals, and soft-touch parts.
  • Castable resin: Burns out cleanly with no ash, designed for lost-wax casting in jewelry and dental work.
  • Water-washable resin: Cleans with water instead of isopropyl alcohol, making post-processing safer and easier, but it is more brittle than standard resin.

How to Choose the Right Material

Start by asking what the part will do. If it’s a decorative model, PLA is the cheapest and easiest. If it needs to survive heat or impacts, move to PETG or ABS. If it must flex, TPU. If it needs to be strong and lightweight, carbon-fiber nylon.

Then check your printer’s specs. The nozzle temperature limit, heated bed capability, and whether the printer is enclosed all constrain your choices. A printer that only reaches 230°C cannot print nylon or polycarbonate. An open-frame printer without an enclosure will struggle with ABS due to warping.

Also consider the environment the part will live in. Outdoor parts need UV resistance (PETG, ASA) and moisture resistance (PETG, polypropylene). Parts near a car engine need high heat resistance (polycarbonate, nylon). Parts that touch food should be made from food-safe materials, but note that the printing process creates microscopic gaps where bacteria can grow, so printed food containers are generally not recommended.

Finally, think about post-processing. PLA is easy to sand and paint. ABS can be smoothed with acetone vapor. Resin parts need washing and curing. Nylon absorbs moisture and may need drying after printing.

Common Problems and Misconceptions

  • Warping: Caused by uneven cooling. ABS and nylon warp most; PLA and PETG warp least. Solutions: use a heated bed, an enclosure, and a brim or raft.
  • Stringing: Thin strands of plastic between parts. Caused by oozing when the nozzle moves. Reduce by lowering temperature and increasing retraction.
  • Layer adhesion: Parts break along layer lines because layers don’t fully fuse. This is worse with PLA (which is brittle) and better with ABS and nylon. Increase nozzle temperature and reduce layer height for stronger bonds.
  • Moisture: Nylon and PETG absorb water from the air, causing steam bubbles and poor surface quality. Dry them in a filament dryer or oven before use.
  • Myth: “All plastics are recyclable in the same bin.” 3D printer waste is usually not accepted in curbside recycling. Some companies offer filament recycling programs, but most waste goes to landfill.
  • Myth: “PLA is biodegradable.” It is compostable only under industrial conditions (high heat and humidity), not in a backyard compost pile.

Safety and Ventilation

All 3D printing materials release volatile organic compounds (VOCs) and ultrafine particles when heated. PLA and PETG are relatively low-emission, but ABS and nylon produce noticeable fumes that can irritate eyes and lungs. Use your printer in a well-ventilated area, ideally with an enclosure and a HEPA filter. Never leave a printer running unattended for long periods, as thermal runaway can cause fires. Resins are skin sensitizers, so always wear nitrile gloves and safety glasses when handling uncured resin, and wash any skin contact immediately with soap and water.

Cost and Storage Considerations

Filament prices vary widely. PLA and PETG are the cheapest, typically $20–$30 per kilogram. ABS is similar. TPU and nylon cost more, around $40–$60 per kilogram. Specialty composites can be $60–$100 per kilogram. Resin is sold by the liter, usually $30–$80, and you also need isopropyl alcohol for cleaning and a UV curing station.

Store all filaments in a dry, sealed container with desiccant. Nylon and PETG are hygroscopic and degrade quickly if left out. PLA and ABS are less sensitive but still benefit from dry storage. Resin must be kept in an opaque, airtight bottle away from sunlight, as UV light will cure it prematurely.

Frequently Asked Questions

Can a 3D printer use any material?

No. FDM printers can only use thermoplastics that melt at a temperature the hotend can reach. SLA printers only use photopolymer resins. SLS printers use nylon or other powders. You cannot switch between these technologies without changing the entire printer.

What is the strongest 3D printing material?

For FDM, polycarbonate and nylon are among the strongest, with PC offering high impact strength and nylon good toughness and flexibility. For SLA, tough resins are designed to be impact-resistant. However, strength also depends on print orientation and infill density, so a well-printed PLA part can be stronger than a poorly printed nylon part.

Is PLA safe for food contact?

PLA is derived from food-safe materials, but the 3D printing process creates tiny gaps between layers where bacteria can grow. Even if you use a food-safe filament, the printed part is not considered food-safe by most standards. If you must print a food-related item, coat it with a food-safe epoxy or use a silicone mold.

Why does my ABS print warp even with a heated bed?

Warping happens because ABS shrinks as it cools, and the bottom layers cool faster than the upper layers. A heated bed helps, but you also need to keep the ambient air warm. An enclosure prevents drafts and maintains a stable temperature. Use a brim or a raft to increase adhesion, and consider printing on a textured PEI sheet.

Can I mix different filaments in one print?

Yes, if your printer has multiple extruders or a filament switching system. You can combine materials with similar melting temperatures, like PLA and PETG, but they may not bond well chemically. For a strong bond, choose materials with similar glass transition temperatures. Some printers allow you to pause and manually swap filament, but this is only practical for simple color changes.

How do I know if my filament is wet?

Wet filament produces popping or hissing sounds during printing, and you’ll see bubbles or steam coming from the nozzle. The surface of the printed part will look rough or have tiny blobs. You can dry it in a filament dryer or a food dehydrator at the recommended temperature for 4–6 hours. Nylon and PETG are the most susceptible; PLA and ABS are less so.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →