AI data centers are exploring solid-state drives (SSDs) because the massive, repetitive data reads required to train and run large language models and other AI workloads are bottlenecked by traditional hard disk drives (HDDs), and SSDs offer the high random read speeds, low latency, and power efficiency needed to keep expensive GPUs and accelerators busy. While HDDs remain cheaper per terabyte for bulk storage, the performance gap is so significant that AI infrastructure operators are increasingly deploying all-flash or hybrid storage tiers to avoid idle compute time. This article explains the technical reasons behind this shift, how SSDs fit into AI data pipelines, and what it means for the future of data center storage.
Formula
The calculator above estimates how long it takes to read a given amount of data from a storage device, based on the time it takes to read 1 TB. The formula is:
Total time (hours) = Data size (TB) × Time to read 1 TB (hours)
- Data size (TB) – the total amount of data you need to read, in terabytes.
- Time to read 1 TB (hours) – the duration it takes the storage system to read one terabyte, which depends on the device’s sustained read speed.
For example, an HDD with a sustained read speed of 250 MB/s takes about 1.1 hours to read 1 TB (1000 GB / 0.25 GB/s ≈ 4000 seconds ≈ 1.1 hours). A modern NVMe SSD with a sustained read speed of 3,500 MB/s reads the same 1 TB in about 4.8 minutes (0.08 hours).
Worked Example
Using the default values in the calculator: you have 100 TB of data to read, and it takes 1 hour to read 1 TB from your storage device.
- Total read time = 100 TB × 1 hour/TB = 100 hours.
The calculator shows 100.00 hours. If you replace the HDD with an SSD that reads 1 TB in 0.08 hours, the same 100 TB would take only 8 hours – a 12.5× improvement.
Why AI Workloads Are Different from Traditional Data
Traditional data center workloads – databases, file servers, backup systems – are often sequential or have moderate read/write ratios. AI training, on the other hand, repeatedly reads the same datasets in random order across thousands of parallel processes. Each training epoch requires the entire dataset to be read again, and the data is often shuffled to prevent the model from memorizing order. This random access pattern is exactly where HDDs perform worst, because they rely on physical read/write heads moving to different disk locations, causing seek times of several milliseconds. SSDs have no moving parts and can access any location in microseconds – a 100–1000× reduction in latency.
Furthermore, AI inference (using a trained model) often requires loading model weights and intermediate activations quickly to serve many user requests. A slow storage tier can cause GPU underutilization, which is costly because GPUs are the most expensive component in an AI cluster. The industry rule of thumb is that a GPU should never wait for data; if it does, the entire training job slows down proportionally.
How SSDs Fit into the AI Data Pipeline
AI data pipelines typically have several stages, each with different storage requirements:
- Raw data ingestion: Incoming data (images, text, sensor readings) is written once and read rarely. HDDs are acceptable here.
- Data preprocessing: Cleaning, resizing, and augmenting data involves many small random reads and writes. SSDs significantly speed up this stage.
- Training data loading: The preprocessed data is read repeatedly and randomly. This is the critical stage – SSDs are essential to avoid GPU starvation.
- Checkpointing: During training, model weights are periodically saved to disk. These are large sequential writes, but they must be fast to not interrupt training. NVMe SSDs are preferred.
- Model serving: Inference requires low-latency reads of model weights and embeddings. SSDs are mandatory for real-time applications.
A common architecture is a tiered storage system: a small, ultra-fast NVMe SSD tier for active training data, a larger SSD tier for recent datasets, and an HDD tier for cold archives. The key is that the SSD tier must be large enough to hold the entire working set of the AI job, otherwise the HDD becomes a bottleneck again.
Comparing SSD Types: SATA, NVMe, and PCIe
Not all SSDs are equal. The main distinction is the interface:
- SATA SSDs: Use the same interface as HDDs, max speed around 550 MB/s. They are cheap but not much faster than high-end HDDs in sequential reads, though random reads are still much better.
- NVMe SSDs: Use the PCIe bus directly, with speeds ranging from 1,500 MB/s (PCIe 3.0) to over 7,000 MB/s (PCIe 5.0). They also have much lower latency and support many more parallel queues, which is crucial for AI’s parallel access patterns.
- Storage-class memory (SCM): A newer category (e.g., Intel Optane, now discontinued) that sits between DRAM and NAND flash, offering even lower latency. While not widely used now, the concept of memory-tiering is being explored.
For AI data centers, NVMe SSDs are the standard choice because they can deliver the high IOPS (input/output operations per second) that training jobs demand. A single NVMe SSD can handle over 1 million random read IOPS, whereas an HDD manages around 200 IOPS. This difference is why a single NVMe drive can replace dozens of HDDs in an AI workload.
Costs and Trade-offs: Why Not All-Flash Everywhere?
The main downside of SSDs is cost. As of 2025, the price per terabyte of enterprise NVMe SSDs is roughly 5–10× higher than enterprise HDDs. For AI datasets that can reach petabytes, the cost difference is enormous. This is why data centers use a tiered approach: keep the hot working set on SSDs, and move cold data to HDDs or tape.
However, the total cost of ownership (TCO) calculation includes more than just drive price. SSDs consume far less power per terabyte, generate less heat, and take up less physical space. For a large AI cluster, the power and cooling savings can offset some of the upfront cost. Additionally, the cost of GPU idle time is so high that even a small performance improvement in storage can justify the SSD premium. A single A100 GPU can cost over $10,000, and if it waits 10% of the time due to slow storage, that’s $1,000 of wasted hardware per GPU per month – often more than the storage cost difference.
Common Problems and Misconceptions
Misconception: SSDs wear out quickly. While it’s true that NAND flash has a limited number of write cycles, modern enterprise SSDs have sophisticated wear-leveling and over-provisioning. For AI workloads that are mostly read-heavy, write endurance is rarely the bottleneck. A typical enterprise SSD rated for 1 drive-write-per-day (DWPD) can last many years under AI read workloads.
Problem: Overheating. High-performance NVMe SSDs generate significant heat under sustained load. Data centers must ensure adequate cooling, otherwise drives throttle and performance drops.
Problem: Firmware bugs. SSDs have complex firmware that can sometimes cause performance degradation or data corruption. Enterprise SSDs are designed with better error correction and power-loss protection than consumer models, which is why AI data centers use enterprise-grade drives.
Misconception: SSDs are always faster. In sequential writes of very large files, some HDDs can approach SSD speeds, and for pure archival storage, HDDs are still more cost-effective. The advantage of SSDs is in random access and parallel workloads – exactly what AI needs.
Alternatives and Future Directions
While SSDs are the current answer, other technologies are being explored:
- Compute Express Link (CXL): A new interconnect that allows memory and storage to be shared across servers. CXL-based memory expansion could reduce the need for large SSD caches by providing faster access to more memory.
- Storage-class memory (SCM): Though Intel discontinued Optane, other vendors are exploring similar technologies. SCM sits between DRAM and NAND, offering near-DRAM latency at a lower cost.
- Data compression and deduplication: Reducing the amount of data that needs to be read can help, but AI datasets often have low redundancy and compression ratios.
- In-storage computing: Some research explores performing simple computations inside the SSD, reducing the data that must be transferred to the CPU. This is still experimental.
For now, the practical answer is that AI data centers are exploring solid-state storage because it is the only technology that can keep up with the random read demands of AI training and inference. The trend is clear: as AI workloads grow, the percentage of SSD capacity in data centers will continue to rise, even if HDDs remain for cold storage.
Frequently Asked Questions
Q: Why can’t AI data centers just use more RAM instead of SSDs?
RAM is faster than SSDs but much more expensive and volatile. A server can have a few hundred GB of RAM, but AI datasets are often terabytes to petabytes. SSDs provide a cost-effective middle tier between RAM and HDDs.
Q: What is the difference between IOPS and throughput?
IOPS measures the number of read/write operations per second, which matters for random small accesses. Throughput measures bytes per second, which matters for large sequential transfers. AI training needs both high IOPS and high throughput, but IOPS is often the limiting factor because of the random access pattern.
Q: Do AI data centers use consumer SSDs or enterprise SSDs?
Enterprise SSDs. They have higher endurance, better error correction, power-loss protection, and consistent performance under sustained load. Consumer SSDs are not designed for 24/7 data center operation.
Q: How much faster is an NVMe SSD compared to an HDD for AI training?
In real-world AI workloads, the difference can be 10–50× in terms of data loading time. The exact number depends on the dataset size, access pattern, and the number of parallel readers. A single NVMe SSD can replace dozens of HDDs.
Q: Is the future of AI storage all-flash?
Probably not entirely. HDDs will remain for cold storage and archives where cost per terabyte is the priority. But the active working set – the data that GPUs need to access frequently – will be almost entirely on SSDs. The ratio will shift toward SSDs as prices drop.
Related
Formula used
in t | Time to read 1 TB | hours | 1 | 0 | 24 in d | Data size | TB | 100 | 0 | 10000 out time | Total read time | hours | d * t | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.
More cards in this drawer
- Infinity Essence in Sailor Piece: Farming and Uses
- Apollo.io Alternatives for Sales Prospecting
- Deploy AI Agents in a Service Desk With Human Oversight
- AIM and Yahoo Profiles: When Did You Last Look?
- Best Smartwatch Under ₹5,000 in India: What to Buy
- Chat History vs Saved Memory in AI Assistants