keepcalculator

06 Numbers and Powers

First Phone with In-Display Fingerprint Sensor

Card No. 06·73093 · Updated · Standard formula, shown below

The world’s first phone with an in-display fingerprint sensor was the Vivo X20 Plus UD, announced in January 2018 and released in China later that month. It used a sensor embedded in the OLED screen that optically scanned your fingerprint when you pressed on a designated area of the display. This article explains how that technology worked, why it took so long to arrive, and what it means for phones today.

Background: Why In-Display Sensors Were Hard

Fingerprint sensors had been on phones for years before 2018, but they were always placed on the front bezel, back cover, or side button. Putting one under the display was difficult for two main reasons:

  • Thickness: Traditional capacitive sensors (like those on the home button of an iPhone or Galaxy) need to be close to your finger. A display stack is several millimeters thick, which blocked the signal.
  • Display technology: LCD panels have a backlight that scatters light and adds layers, making it nearly impossible for an optical sensor to see through. OLED displays are self-emissive, meaning each pixel produces its own light, and the layers are thinner, so light can pass through gaps between pixels.

Vivo solved the problem by using an OLED panel and a tiny optical sensor placed directly behind the screen. When you pressed your finger on the sensor area, the screen lit up that region, and the sensor captured a 2D image of your fingerprint through the gaps in the pixel array.

How the First In-Display Sensor Worked

The Vivo X20 Plus UD used a CMOS optical sensor made by Synaptics (model FS9500). Here’s the basic process:

  1. Your finger touches the glass over the designated sensor area.
  2. The OLED pixels in that area emit light, which illuminates your fingerprint ridges.
  3. Light reflects off your finger and passes back through the display layers.
  4. A tiny camera-like sensor under the screen captures the reflected light pattern.
  5. The phone compares that pattern to the stored fingerprint data and unlocks if it matches.

This is fundamentally different from the capacitive sensors used before, which measure electrical differences between ridges and valleys. Optical sensors rely on light, so they work best with a bright screen and a clean, dry finger.

Why It Took So Long to Reach the Market

Companies had been demonstrating in-display prototypes for years, but commercializing them was a challenge. The main hurdles were:

  • Yield rates: The sensor had to be perfectly aligned under the display, and any dust or misalignment ruined the module. Early production yields were low, driving up cost.
  • Sensor size: Early optical sensors were relatively large, which limited where they could be placed and how small the phone could be.
  • Security concerns: A 2D optical image is easier to fool with a printed fingerprint than a 3D capacitive scan. Manufacturers had to add liveness detection (like checking for blood flow) to make it secure enough for payments.
  • Speed: Early in-display sensors were noticeably slower than the instant capacitive sensors users were used to. Vivo’s first implementation took about 0.5 seconds, which felt sluggish.

Ultrasonic vs. Optical: The Two Main Types

After Vivo’s debut, other manufacturers adopted two different approaches:

  • Optical (used by Vivo, OnePlus, Xiaomi, and most Android phones): Uses light to capture a 2D image. Works well on OLED screens, is cheaper, and is now very fast. However, it can be fooled by a high-resolution printed fingerprint, and it doesn’t work well with wet or very dry fingers.
  • Ultrasonic (used by Samsung on the Galaxy S10 and later): Uses sound waves to map the ridges and valleys in 3D. It works with wet fingers and is harder to fool, but it’s more expensive and can be affected by screen protectors.

Today, most mid-range and flagship Android phones use an optical in-display sensor, while Samsung and a few others use ultrasonic. Apple has never used an in-display sensor on the iPhone, sticking with Face ID instead.

Common Problems and Misconceptions

Owners of early in-display sensor phones often complained about these issues:

  • Slow unlock: The first generation took about half a second, which felt like an eternity compared to the instant response of capacitive sensors.
  • Screen protector interference: Thick glass or plastic protectors could block the optical signal or confuse the ultrasonic sensor. Many phones had to add a “increase touch sensitivity” setting to compensate.
  • Bright flash at night: Optical sensors light up the screen area to scan, which can be blinding in a dark room. Some phones dim the flash or use a lower brightness, but it’s still noticeable.
  • Misconception: It scans the entire screen. In reality, the sensor is only in a small, fixed area (usually near the bottom center). You have to press exactly on that spot, which is why some users found it less convenient than a rear sensor.

Cost and Adoption

When the Vivo X20 Plus UD launched, it was priced around $570 in China, which was only slightly more than the regular X20. The sensor itself added roughly $10–$15 to the bill of materials, a cost that has dropped significantly since then. Today, in-display sensors are found on phones as cheap as $150, making them a standard feature on most Android devices. The technology is now mature enough that it’s no longer a premium differentiator.

How to Choose a Phone with an In-Display Sensor

If you’re shopping for a phone with an in-display fingerprint sensor, consider these factors:

  • Type: Optical sensors are fine for most people, but if you often have wet hands or use a thick screen protector, an ultrasonic sensor (like on Samsung flagships) may be more reliable.
  • Position: Some sensors are placed too low or too close to the edge, making them awkward to reach. Try the phone in a store if possible.
  • Speed: Modern optical sensors are nearly as fast as capacitive ones, but budget models may still be slower. Check reviews for real-world unlock speed.
  • Screen protector compatibility: Look for protectors specifically labeled “fingerprint compatible” or “ultrasonic compatible.” Some phones have a setting to increase sensitivity after applying a protector.

Frequently Asked Questions

Is the Vivo X20 Plus UD the first phone with an in-display fingerprint sensor?

Yes, it was the first commercially available phone with an in-display fingerprint sensor. Vivo announced it in January 2018 and released it in China later that month. Some earlier prototypes existed, but the X20 Plus UD was the first you could actually buy.

Why doesn’t the iPhone have an in-display fingerprint sensor?

Apple has not used an in-display sensor on any iPhone. Instead, it relies on Face ID for biometric authentication. Apple’s design philosophy favors a seamless front, and Face ID allowed them to remove the home button entirely. There have been rumors of an under-display Touch ID, but as of now, no iPhone has shipped with one.

Can an in-display fingerprint sensor be fooled by a printed fingerprint?

Optical sensors can be fooled by a high-resolution printed fingerprint, which is why many phones incorporate liveness detection (like checking for pulse or sweat). Ultrasonic sensors are harder to fool because they map 3D structure, but no sensor is 100% foolproof. For high-security applications, use a strong PIN instead.

Does an in-display sensor work with a screen protector?

Yes, but it depends on the type and thickness. Thin glass or film protectors usually work fine. Thick glass or privacy protectors can block the optical signal or confuse the ultrasonic sensor. Many phones have a “touch sensitivity” setting to help, but if you have issues, try a different protector.

Why did it take so long for in-display sensors to become common?

The main challenges were technical: making a sensor thin enough to fit under the display, ensuring it worked reliably through the screen layers, and keeping costs down. OLED displays were also necessary, and they only became standard on mid-range phones in recent years. Once those pieces fell into place, adoption was rapid.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →