keepcalculator

06 Numbers and Powers

NAS Beyond Plex: 3 More Services to Run

Card No. 06·78497 · Updated · Standard formula, shown below

Your NAS is not just for Plex. Beyond media streaming, a NAS can host your personal cloud storage, run automated backup for all your devices, and serve as a private ad-blocker for your whole network. This article explains three practical services—Nextcloud, Syncthing, and Pi-hole—what they do, how they work, and how to get started.

Why Run More Than Plex on Your NAS?

Most people buy a NAS (Network Attached Storage) to store files and stream media with Plex. But a NAS is a small always-on computer, and it can do much more. Running extra services turns it from a passive storage box into an active part of your home network. The main benefits are privacy (your data stays on your hardware), convenience (services are available from any device), and cost (you avoid monthly cloud subscriptions). The trade-off is that each service uses some CPU, RAM, and attention. Modern NAS units with at least 2GB of RAM can comfortably run Plex plus one or two of these services.

Service 1: Nextcloud – Your Private Cloud Storage

Nextcloud is an open-source platform that gives you file sync, sharing, contacts, calendar, and even office editing—all hosted on your own NAS. It works like Dropbox or Google Drive, but you control the data. You install it via your NAS’s app store (or Docker), then access it through a web browser or mobile app. Files are stored on your NAS, and you can share links with others. Nextcloud also supports end-to-end encryption and two-factor authentication for security. It’s ideal if you want to replace cloud storage subscriptions or if you need a central place to sync files across devices without sending them to a third party.

Service 2: Syncthing – Continuous File Sync

Syncthing is a peer-to-peer file synchronization tool. Unlike Nextcloud, there is no central server—it directly syncs folders between your devices (phone, laptop, desktop, NAS) over your network or the internet. It is especially useful for keeping documents, photos, or project files identical on multiple machines without manual copying. You install Syncthing on your NAS and on each device, then pair them with a device ID. It runs continuously, detecting changes and syncing them in real time. Because it is peer-to-peer, there is no cloud intermediary, so your files never touch a server you don’t control. Syncthing is lightweight and can run on low-power NAS models.

Service 3: Pi-hole – Network-Wide Ad Blocking

Pi-hole is a network-level ad blocker that works by acting as a DNS sinkhole. When you install it on your NAS, it intercepts DNS queries from all devices on your home network and blocks requests to known advertising and tracking domains. The result: ads disappear from websites and apps on every device—phones, smart TVs, desktops—without installing anything on each device. It also speeds up browsing because it refuses to load ad content. Pi-hole runs as a small service and needs only a few hundred MB of RAM. It does not block all ads (some apps use hardcoded IPs), but it is very effective for most web ads. You can also use it to see which devices are making the most DNS queries.

How to Choose Which Service to Install

Your choice depends on your needs and your NAS hardware. Here is a quick guide:

  • Nextcloud – if you want a full cloud experience with file sharing, calendar, and contacts. Needs more RAM (2GB+ recommended) and a database (SQLite or MySQL).
  • Syncthing – if you only need file sync between a few devices, no sharing or extra features. Very lightweight, runs on 512MB RAM or less.
  • Pi-hole – if you want to block ads on all devices. Very light, but requires you to change your router’s DNS settings to point to your NAS.

You can run all three if your NAS has enough resources, but start with one to avoid overloading the CPU. Check your NAS’s app store for one-click installs, or use Docker for more control.

Common Setup Problems and How to Fix Them

Setting up these services is usually straightforward, but you may hit a few common issues. For Nextcloud, the most frequent problem is a “untrusted domain” error—you need to add your NAS’s IP or domain to the config.php file. For Syncthing, the issue is often firewall settings: you must open port 22000 for incoming connections. For Pi-hole, the biggest mistake is not changing the router’s DNS server; if you don’t, devices will ignore Pi-hole. Also, if you use a VPN, DNS requests may bypass Pi-hole, so you may need to configure the VPN to use Pi-hole as its DNS. Always check the logs in each service’s web interface for clues.

Security and Maintenance Tips

Running services on your NAS exposes them to the network, so take basic precautions. Enable HTTPS for Nextcloud (using a reverse proxy like Nginx or Caddy). Use strong passwords and enable two-factor authentication where possible. Keep your NAS firmware and the services updated to patch vulnerabilities. For Pi-hole, you must update its blocklists regularly (it has a built-in updater). For Syncthing, ensure your devices are authenticated with the device ID, and consider enabling TLS. Also, do not expose these services directly to the internet unless you are comfortable with the risks; use a VPN like WireGuard to access them remotely instead.

Frequently Asked Questions

Can I run these services alongside Plex on the same NAS? Yes, but it depends on your NAS’s CPU and RAM. Plex transcoding is CPU-intensive, so if you have a low-power model (e.g., an ARM-based NAS), adding Nextcloud may slow things down. Syncthing and Pi-hole are light and usually fine. If you have an Intel Celeron or better, you can likely run all three.

Do I need Docker to install these? No. Most NAS brands (Synology, QNAP, etc.) have official packages for Nextcloud and Syncthing in their app stores. Pi-hole is often available as a Docker container, but you can also install it manually. Docker is convenient for isolation and updates, but not required.

Will Pi-hole slow down my internet? No, it usually speeds it up because it blocks ads before they load. The DNS resolution is fast, and Pi-hole caches responses. The only delay is if the Pi-hole service is down, which would cause DNS failures—so make sure it runs reliably.

Can I access Nextcloud from outside my home? Yes, but you need to set up port forwarding on your router or use a reverse proxy. For security, it’s better to use a VPN. Many NAS models have built-in DDNS and reverse proxy support, but you must configure them carefully.

Is Syncthing safe for sensitive files? Yes, Syncthing uses TLS encryption for data in transit, and you can enable untrusted device mode for extra security. However, files are stored unencrypted on each device, so if a device is stolen, the data is readable. For sensitive data, consider using encrypted folders (Syncthing supports this) or a separate encryption layer.

What if my NAS is too weak to run these? If you have a very old or low-end NAS, you can still run Pi-hole (it’s tiny) and Syncthing (it’s also light). Nextcloud might be too heavy. In that case, consider using a Raspberry Pi as a separate server, or upgrade your NAS’s RAM if possible.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →