You should own at least three drills because no single drill can efficiently handle the full range of drilling and driving tasks found in a typical home or workshop. One drill for light, everyday work, one for heavy-duty driving and boring, and one for precise, small-diameter holes covers nearly every situation without constant bit changes or risking damage to your materials.
The Three-Drill Setup
The most practical trio is a compact 12V drill/driver, a full-size 18V or 20V drill/driver, and a dedicated impact driver. Each tool is optimized for a different job, and having all three means you are not constantly swapping bits or compromising on performance.
- Compact drill/driver: Light, short, and easy to control. Ideal for cabinet hardware, small screws, and working in tight spaces like inside a cabinet or under a sink.
- Full-size drill/driver: The workhorse. Handles large hole saws, spade bits, mixing paint, and driving long screws into dense wood. More torque and battery capacity than a compact model.
- Impact driver: Delivers rapid, high-torque rotational impacts. Perfect for driving long screws, lag bolts, and self-tapping screws without stripping the head or burning out the motor.
Many manufacturers sell these three as a combo kit, which is often cheaper than buying them separately and also gives you two batteries and a charger that work with all three tools.
What Each Drill Does Best
Understanding the strengths of each type helps you decide if you need all three or can get by with two.
Drill/Driver
A standard drill/driver has a chuck that accepts round-shank bits. It offers variable speed and a clutch that stops rotation at a set torque, which is essential for driving screws without sinking them too deep or stripping the head. It is also the only tool in the trio that can bore holes with twist bits, spade bits, hole saws, and Forstner bits.
Impact Driver
An impact driver uses a hexagonal collet that accepts 1/4-inch hex-shank bits. It applies rotational impacts—a series of rapid hammer blows—that drive screws with far more force than a drill/driver. This makes it the go-to for decking screws, drywall screws, and any fastener longer than about 2 inches. The impact action also reduces the reaction torque felt by your wrist, so it is less tiring to use for long periods.
Why Not Just One?
A single drill/driver can technically do both drilling and driving, but you will constantly switch between drill bits and driver bits. More importantly, a compact drill lacks the torque for large holes, and a full-size drill is too bulky for delicate work. An impact driver alone cannot drill holes because it lacks a chuck. So, one tool forces compromises that slow you down and increase the risk of mistakes.
How to Choose Your Three Drills
When selecting your trio, focus on battery platform, chuck size, and ergonomics.
- Stick to one battery system: Buying all three from the same brand (or the same battery platform, like 18V or 20V) means you can share batteries and chargers. This saves money and reduces clutter.
- Chuck size: A 3/8-inch chuck is common on compact drills and handles most bits up to 3/8-inch. A 1/2-inch chuck is standard on full-size drills and accepts larger bits like spade bits and hole saws.
- Torque rating: Measured in inch-pounds (in-lb) or Newton-meters (Nm). For a full-size drill, look for at least 500 in-lb (56 Nm) of torque. For an impact driver, 1,000 in-lb (113 Nm) is a good baseline. Compact drills are usually around 250 in-lb (28 Nm), which is plenty for cabinet screws.
- Speed range: A two-speed gearbox (low/high) is standard. Low speed (0-400 RPM) for driving screws, high speed (0-1,500 RPM) for drilling. Some models offer a brushless motor, which is more efficient and has no brushes to wear out.
- Weight and balance: Hold the tool in the store. A well-balanced drill reduces fatigue. Compact drills should feel light (under 3 lbs / 1.4 kg). Full-size drills will be heavier but should still feel controllable.
Common Problems and Misconceptions
One of the biggest misconceptions is that an impact driver is just a more powerful drill. In reality, it is a different tool. Impact drivers are not meant for drilling holes. They lack the precision and the chuck to hold a round-shank bit securely. Using a hex-shank drill bit in an impact driver is possible, but the impact action can cause the bit to wobble, leading to oversized or angled holes in wood.
Another common issue is stripping screws. This happens when the driver applies too much torque or the clutch is set too high. A drill/driver with a clutch lets you dial in the exact torque, so you can stop the screw flush with the surface. An impact driver does not have a clutch, so you must rely on feel and the tool’s speed to avoid overdriving. Practice on scrap wood to get a sense of how the tool behaves.
Battery life is another pain point. A compact 12V battery will drain quickly if you use it for heavy drilling. That is why the trio works well: you use the compact for light work where it lasts, and the full-size for heavy work where the bigger battery is needed.
Cost and Value
Buying three drills can seem expensive, but it is often cheaper than you think. A basic 12V drill/driver can cost under $50. A full-size 18V drill/driver is typically $80–$150. An impact driver is usually $100–$150. Buying them as a combo kit (often with two batteries and a charger) can save 20–30% compared to buying each separately. Over a decade of use, the cost per project is minimal.
If you are on a tight budget, start with a full-size drill/driver and add the compact and impact driver later. Many people find the impact driver is the most transformative addition, as it makes driving screws noticeably faster and easier.
Safety and Maintenance
All three drills are safe if used correctly. Always wear safety glasses when drilling or driving, as chips and debris can fly. When drilling into walls, use a stud finder to avoid electrical wires and pipes. When driving screws, keep your hands clear of the bit and the workpiece.
Maintenance is simple: keep the chuck clean, occasionally lubricate the chuck jaws with a dry lubricant, and store batteries at room temperature. Do not expose batteries to extreme heat or cold, and use the correct charger for the battery type. If a battery no longer holds a charge, recycle it properly.
Alternatives to Three Drills
If you absolutely want to minimize tools, a single high-quality 18V drill/driver with a good clutch and a second battery can handle most tasks. You can also buy a right-angle attachment for tight spaces and a hex-shank adapter to use driver bits. However, you will still face the annoyance of switching bits and the risk of overdriving screws without an impact driver.
Another alternative is a corded drill, which offers unlimited runtime and lower cost, but you are tethered to an outlet. Cordless is the standard for most people because of convenience.
Frequently Asked Questions
Can I use an impact driver for drilling?
You can use hex-shank drill bits in an impact driver, but it is not recommended for precise holes. The impact action causes the bit to wobble, producing oversized or angled holes, especially in metal. For clean holes, use a drill/driver.
What is the difference between a drill and an impact driver?
A drill/driver has a chuck that holds round-shank bits and offers a clutch to control torque. An impact driver has a hex collet and uses rotational impacts to drive screws with high torque but no clutch. Drills are for boring holes; impact drivers are for driving fasteners.
Is a 12V drill enough for most home tasks?
For light tasks like assembling furniture, hanging curtains, and driving small screws, a 12V drill is sufficient. It is lighter and easier to handle. For drilling larger holes or driving long screws, you will need a full-size 18V/20V drill.
Should I buy a brushless drill or a brushed one?
Brushless motors are more efficient, last longer, and provide more power than brushed motors. They cost more upfront but are worth it if you use the drill frequently. For occasional DIY, a brushed drill is perfectly fine and cheaper.
Can I mix batteries from different brands?
No. Battery packs are proprietary to each brand and often to each voltage class. Always use the same brand and voltage for your tools to ensure compatibility and safety.
What is the best way to avoid stripping screws?
Use the correct driver bit (usually a #2 Phillips or #2 square), press firmly, and set the clutch on a drill/driver to a low setting, then increase until the screw sits flush. For an impact driver, start slowly and let the tool do the work.
Related
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.
More cards in this drawer
- Car Trends Making Cars Worse: 7 Downsides
- Nostalgic Classic Games Revamped on G2A?
- Nvidia RTX 4000 Super GPUs: Full Specs & Buying Guide
- Photoshop vs Lightroom AI Features Compared
- DNF vs DNF5: Which Package Manager?
- Korean SUV Making BMW and Audi Owners Question Their Choices?