keepcalculator

06 Numbers and Powers

Best Soundbar Sound: PCM Settings Explained

Card No. 06·84167 · Updated · Standard formula, shown below

To get the best sound from your soundbar, set its input mode to PCM (Pulse-Code Modulation) for stereo sources and use a direct HDMI connection, while letting your TV handle any surround sound decoding. PCM is the uncompressed digital audio format that preserves the original recording without the lossy compression of Dolby Digital or DTS, so for music, dialogue, and most TV shows, it delivers the clearest, most accurate sound your soundbar can produce.

What Is PCM and Why Does It Matter?

PCM stands for Pulse-Code Modulation, a digital representation of an analog signal. When a CD, streaming service, or TV broadcast plays audio, the sound wave is sampled thousands of times per second and each sample is stored as a number. That stream of numbers is PCM. It is the standard format for CDs, WAV files, and the uncompressed audio track on many Blu-rays and streaming platforms.

Soundbars receive audio from your TV or media player through HDMI, optical, or Bluetooth. The source sends either a PCM stream or a compressed bitstream like Dolby Digital or DTS. Compressed formats reduce file size by discarding audio data that is supposed to be inaudible, but they can introduce artifacts, especially at low bitrates. PCM contains every bit of the original recording, so it is the most faithful representation your soundbar can reproduce.

How PCM Works in a Soundbar Setup

When you connect a device to your TV, the TV can either pass through the audio untouched or process it. If the source sends PCM, the TV usually passes it straight to the soundbar over HDMI ARC or eARC. If the source sends a compressed bitstream, the TV can decode it into PCM before sending it, or it can pass the bitstream through and let the soundbar decode it.

Most soundbars can decode Dolby Digital and DTS themselves, but they all handle PCM natively. The key is to set your TV’s audio output to PCM so the TV does not re-encode or alter the signal. On many TVs, this setting is labeled “PCM,” “Linear PCM,” or “Auto.” Choosing PCM ensures the soundbar receives a clean, uncompressed signal.

For stereo content, PCM is always the best choice. For surround sound, your soundbar may need a compressed bitstream to recreate 5.1 or 7.1 channels, but many modern soundbars can accept multichannel PCM over eARC, which is even better because it is lossless.

How to Set Your Soundbar to PCM

Setting your soundbar to PCM is usually done on the TV, not the soundbar itself. Here are the general steps:

  • Open your TV’s settings menu.
  • Navigate to “Sound,” “Audio,” or “Speaker Settings.”
  • Look for “Digital Audio Out,” “Audio Format,” or “HDMI Audio.”
  • Select “PCM” or “Linear PCM.” If you see “Auto,” that usually means the TV will send PCM for stereo and bitstream for surround, which is fine for most content.
  • On the soundbar itself, check the input mode. Many soundbars automatically detect the incoming format, but some have a button or menu to cycle through “PCM,” “Dolby Digital,” and “DTS.” Choose PCM for stereo sources.

If your soundbar has a display, it will often show “PCM” when receiving that format. If you are using an optical cable, the TV must be set to PCM because optical does not have enough bandwidth for multichannel PCM, so the TV will downmix to stereo PCM.

PCM vs. Dolby Digital vs. DTS: What’s the Difference?

Dolby Digital and DTS are lossy compression codecs. They reduce the data rate by removing sounds that are masked by louder ones, which is efficient but not perfect. PCM is uncompressed, so it preserves everything. For stereo music, PCM is clearly superior. For surround sound, the difference is less noticeable because the compression is designed to be transparent at typical bitrates, but lossless PCM (or Dolby TrueHD and DTS-HD MA) is still the gold standard.

Many streaming services use Dolby Digital Plus, which is a more efficient version of Dolby Digital. When your TV outputs PCM, it decodes that bitstream and sends the decoded audio to the soundbar. This means the soundbar gets the exact same audio the TV decoded, without any further processing. If you set the TV to “Bitstream,” the soundbar does the decoding, which can be better if your soundbar has a superior decoder, but it can also cause audio sync issues or missing channels if the soundbar does not support the format.

Common Problems and Misconceptions

One common misconception is that PCM is always the best setting for every situation. That is not true. If you are watching a movie with a 5.1 Dolby Digital track and your soundbar supports it, sending the bitstream directly to the soundbar can give you true surround sound. Setting the TV to PCM would downmix everything to stereo, losing the surround channels. So the best setting depends on the content and your equipment.

Another issue is audio lag. Some TVs introduce delay when they process audio, especially if they are doing any conversion. If you notice lip-sync issues, try switching the TV to “Pass Through” or “Bitstream” so the soundbar does the decoding, which often reduces latency. Conversely, if your soundbar is slow to decode, PCM might have less lag because it is simpler.

If you hear no sound or a loud static noise after switching to PCM, check that your HDMI cable supports ARC or eARC. Older HDMI cables may not have the bandwidth for high-resolution PCM. Also, make sure the soundbar is connected to the ARC-labeled HDMI port on the TV.

Choosing the Right Connection for PCM

The best connection for PCM is HDMI eARC, which supports high-bandwidth, multichannel PCM up to 7.1 channels. HDMI ARC (without the “e”) supports stereo PCM and compressed 5.1, which is fine for most TV speakers but limits you to two channels for PCM. Optical cables also support stereo PCM and compressed 5.1, but not multichannel PCM.

  • HDMI eARC: Best for PCM, supports up to 7.1 channels and high sample rates.
  • HDMI ARC: Supports stereo PCM and compressed 5.1, but not multichannel PCM.
  • Optical: Supports stereo PCM and compressed 5.1, but not multichannel PCM.
  • Bluetooth: Uses a lossy codec, so it is not ideal for PCM fidelity.

If you have a TV with eARC and a soundbar with eARC, use that connection and set the TV to “Pass Through” or “Auto” to get the best possible audio. If you only have ARC, set the TV to PCM for stereo content and Bitstream for surround content, depending on what you are watching.

Frequently Asked Questions

Should I set my TV to PCM or Bitstream?

For stereo content like music and most TV shows, set it to PCM for the cleanest sound. For surround sound movies, set it to Bitstream if your soundbar supports Dolby Digital or DTS, so you get the full surround mix. If your soundbar is connected via eARC, you can often use “Auto” and let the TV decide, which is the most convenient.

Does PCM make dialogue clearer?

Yes, PCM can make dialogue clearer because it preserves the full frequency range and dynamic range of the original recording, without the artifacts of lossy compression. However, the biggest factor in dialogue clarity is the soundbar’s center channel and its placement, so even with PCM, a poorly placed soundbar will not fix muffled speech.

Why does my soundbar say “PCM” but I don’t hear surround sound?

That means the source is sending a stereo PCM signal. If you are watching a 5.1 movie, the TV may be downmixing it to stereo because the connection (optical or ARC) cannot carry multichannel PCM. To get surround sound, switch the TV to Bitstream so it sends the compressed 5.1 track to the soundbar, or use an eARC connection.

Is PCM the same as Dolby TrueHD?

No, but they are related. Dolby TrueHD is a lossless compression format that, when decoded, becomes PCM. The soundbar receives the TrueHD bitstream and decodes it into PCM internally. If your TV decodes TrueHD and sends PCM to the soundbar, you get the same result, but only if the connection supports the bandwidth.

Can I use PCM for gaming?

Yes, PCM is often the best choice for gaming because it has the lowest latency and preserves the positional audio cues that games rely on. Many consoles output PCM by default, and you should keep that setting. If you have a surround sound setup, make sure your console is set to output multichannel PCM over HDMI.

Does PCM require more bandwidth than Dolby Digital?

Yes, PCM is much larger. A stereo PCM stream at 48 kHz/16-bit is about 1.5 Mbps, while Dolby Digital is typically 192 kbps. Multichannel PCM can be several times larger, which is why eARC is needed for 5.1 or 7.1 PCM. If your connection cannot handle it, the TV will downmix to stereo.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More cards in this drawer

The whole Numbers and Powers drawer →