You should hone a blade after sharpening it, not before. Sharpening removes metal to create a new edge; honing realigns that edge without removing material, so it is the final step that leaves the blade cutting smoothly.
What Sharpening and Honing Actually Do
Sharpening and honing are often confused because both involve running a blade along an abrasive surface. But they serve different purposes and remove different amounts of steel.
- Sharpening grinds away metal to form a new edge. It uses coarse abrasives (stones, wheels, or grinders) to reshape the blade when it is dull, chipped, or has lost its original angle.
- Honing straightens the microscopic burrs and misalignments that develop along an otherwise sharp edge. It uses a fine abrasive (steel rod, ceramic rod, or strop) and removes almost no metal.
Think of sharpening as rebuilding a wall and honing as smoothing the mortar. You cannot smooth a wall that hasn’t been built; similarly, honing a dull blade just polishes a blunt edge and does nothing to make it cut better.
Why Hone After Sharpening
When you sharpen a blade, the process leaves a fragile, slightly curled burr along the edge. This burr is a thin lip of metal that folds over during grinding. If you stop after sharpening, the blade may feel sharp but will dull quickly and may even feel rough when cutting.
Honing after sharpening does two things:
- Removes or folds down the burr, leaving a clean, uniform edge.
- Realigns any microscopic teeth that were bent during sharpening.
This is why professional knife sharpeners almost always finish with a honing pass. The same logic applies to straight razors, chisels, and plane blades—the final honing step is what takes the edge from “sharp” to “keen.”
What If You Hone Before Sharpening?
Honing before sharpening is not harmful, but it is wasted effort. A dull blade has no edge to realign; the metal is already rounded or chipped. Running a steel or strop over it will only polish the dull surface, and you will still need to sharpen it anyway.
There is one exception: if you are about to sharpen a blade that has been sitting for a while, a quick hone can remove light surface rust or residue, making the sharpening step cleaner. But this is a minor convenience, not a necessary step. In practice, you should always sharpen first to create the edge, then hone to perfect it.
How Often to Hone vs. Sharpen
The frequency depends on how often you use the blade and what you cut. A good rule of thumb is to hone every few uses and sharpen only when honing stops restoring the edge.
- Hone after every 2–4 uses, or whenever the blade feels less smooth but still cuts.
- Sharpen when the blade fails to cut through a tomato skin or paper without tearing, which is a common test for kitchen knives.
For straight razors, honing on a strop is done before every shave, while sharpening on a stone is needed only every few months. For woodworking tools, hone after every sharpening session and periodically during use.
Common Mistakes and Misconceptions
One widespread myth is that a honing steel “sharpens” a knife. It does not—it only realigns the edge. If you rely solely on a steel, your knife will gradually become duller until it needs real sharpening.
Another mistake is applying too much pressure when honing. Honing should be light; heavy pressure can bend the edge too far and cause it to break off. Use just enough pressure to keep the blade in contact with the rod or strop.
People also often hone at the wrong angle. The honing angle should match the blade’s existing edge angle, typically 15–20 degrees for kitchen knives. If you hold the blade too steep, you’ll round the edge instead of straightening it.
How to Hone Properly
Whether you use a steel, ceramic rod, or strop, the technique is similar:
- Hold the honing rod vertically with the tip resting on a cutting board or towel.
- Place the heel of the blade against the top of the rod at the correct angle (usually 15–20 degrees).
- Draw the blade down and across the rod, moving from heel to tip, so the entire edge passes over the rod.
- Repeat on the other side of the rod with the other side of the blade.
- Alternate sides for 5–10 passes each, using light pressure.
For a strop, lay it flat and draw the blade away from the edge (spine first) with light pressure, then flip and repeat on the other side.
When to Skip Honing Entirely
If your blade is severely dull, chipped, or has a rolled edge, honing won’t help. You need to sharpen first. Honing is only effective on a blade that is already sharp but has lost its perfect alignment.
Also, some blades are not meant to be honed. Serrated knives, for example, are difficult to hone and are usually sharpened with a specialized rod. Ceramic blades are very hard and brittle; honing them can cause chipping, so they typically require professional sharpening instead.
Frequently Asked Questions
Can I use a honing steel on a dull knife?
Yes, but it won’t make it sharp. A steel only realigns the edge; if the blade is dull, you need to sharpen it with a stone or grinder first. Using a steel on a dull knife is like brushing your teeth before flossing—it does something, but not the main job.
How do I know if my blade needs sharpening or just honing?
Try cutting a ripe tomato or a piece of paper. If the blade slices cleanly with minimal pressure, it just needs honing. If it crushes or tears, it needs sharpening. A blade that fails the tomato test after honing is truly dull.
Does honing wear out the blade?
No, honing removes virtually no metal, so it does not wear out the blade. Sharpening does remove metal, which is why you should hone as often as possible to delay the need for sharpening.
What angle should I hone at?
Match the angle of the existing edge. Most Western kitchen knives have a 20-degree angle per side, while Japanese knives are often 15 degrees. If you’re unsure, check the manufacturer’s recommendation or use a sharpening guide.
Can I hone a straight razor with a steel?
No, a steel is too coarse for a straight razor. Use a leather strop, which is fine enough to realign the delicate edge without damaging it. Steels are meant for thicker kitchen or hunting knives.
Related
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.
More cards in this drawer
- Car Trends Making Cars Worse: 7 Downsides
- Nostalgic Classic Games Revamped on G2A?
- Nvidia RTX 4000 Super GPUs: Full Specs & Buying Guide
- Photoshop vs Lightroom AI Features Compared
- DNF vs DNF5: Which Package Manager?
- Korean SUV Making BMW and Audi Owners Question Their Choices?